Tables - ABB Power2 850-M Operation Manual

Operation Manual / Power2 850-M / Low-pressure stage

Tables

Tables
Table 1: Definition of pictograms .............................. 11
Table 2: Personal protective equipment to be worn
at all times ...................................................................... 15
Table 3: Personal protective equipment to be worn
specific to the respective task ................................... 15
Table 4: Operating limits ............................................. 19
Table 5: Recommended replacement intervals ....... 19
Table 6: Further data .................................................... 19
Table 7: Swivel lifting eyes to be used ..................... 30
Table 8: Transporting the low-pressure stage....... 30
Table 9: Pre-lubrication time....................................... 33
Table 10: Post-lubrication time .................................. 33
Table 11: Filter mesh width......................................... 34
Table 12: Oil pressure range ....................................... 38
Table 13: Lubricating oil temperature ...................... 39
Table 14: Expected replacement intervals [h]......... 48
Table 15: Maintenance intervals ................................ 50
Table 16: Cleaning parameters Power2 LP .............. 53
Table 17: Cleaning parameters Power2 HP.............. 53
Table 18: Operating point for turbine cleaning...... 56
Table 19: Cleaning parameters HP ............................. 57
Table 20: Cleaning parameters LP ............................. 57
Table 21: Holding time.................................................. 57
Table 22: Surface of the flow channel....................... 58
Table 23: Tightening torque (81272).......................... 61
Table 24: Tightening torque (81273).......................... 61
Table 25: Malfunctions when starting - Delayed
start-up .......................................................................... 64
Table 26: Malfunctions when starting - Vibrations.....
64
Table 27: Malfunctions when starting - Rubbing of
rotating parts................................................................ 64
Table 28: Malfunctions during operation - Lubricat-
ing oil pressure too low............................................... 65
Table 29: Malfunctions during operation - Power2
LP speed reductions .................................................... 65
© Copyright 2022 ABB. All rights reserved.
Table 30: Malfunctions during operation - Power2
HP speed reductions..................................................... 65
Table 31: Malfunctions during operation - Power2 LP
speed increases ............................................................. 65
Table 32: Malfunctions during operation - Power2
HP speed increases ....................................................... 66
Table 33: Malfunctions during operation - Exhaust
gas temperature too high............................................ 66
Table 34: Malfunctions during operation - Charge
air pressure too low ...................................................... 67
Table 35: Malfunctions during operation - Charge air
pressure too high .......................................................... 67
Table 36: Malfunctions during operation - Com-
pressor 1 contamination .............................................. 68
Table 37: Malfunctions during operation - Com-
pressor 2 contamination.............................................. 68
Table 38: Surging of the low-pressure or high-pres-
sure stage........................................................................ 69
Table 39: Malfunctions when stopping - Runout
noises ............................................................................... 70
Table 40: Malfunctions when stopping - Runout
time too short ................................................................ 70
Table 41: Measured speed incorrect .......................... 70
Table 42: Weights of the assemblies ......................... 73
Table 43: Axial clearance A ........................................... 76
Table 44: Tightening torque (56017) ......................... 84
Table 45: Tightening torque (61056) ......................... 85
Table 46: Tightening torque (42087)......................... 87
Table 47: Control dimension X .................................... 88
Table 48: Tightening torque (61037 / 72021) ........... 89
Table 49: Tightening torque (77016) ......................... 90
Table 50: Tightening torque (72002) ......................... 91
Table 51: Axial clearance A ........................................... 92
Table 52: Tightening torque (72004) ......................... 93
Table 53: Tightening torque (72004 / 77022) .......... 94
Table 54: Tightening torques...................................... 96
Table 55: Cover plate / gasket .................................... 98
Table 56: Tightening torque (42087) ......................... 99
HZTL4062_EN Revision E March 2022