Related Manuals for Inspire ST3
Summary of Contents for Inspire ST3
- Page 1 Model # ST3.1PK USER MANUAL START HERE STRIDER Strider with 10” Touchscreen Display Record Serial Number Here Health in Motion LLC V12092021...
-
Page 2: Table Of Contents
BEFORE YOU BEGIN Welcome to the Inspire Fitness Family! Thank you for choosing the Inspire Fitness ST3 Strider. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to providing you complete customer satisfaction. -
Page 3: Important Safety Notice
IMPORTANT SAFETY NOTICE Precautions This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. Please note the following safety precautions: Keep children and pets away from the machine at all times. -
Page 4: Contents Of Packaging
CONTENTS OF PACKAGING Pg. 4 V12092021... -
Page 5: Warning And Important Label Placement
WARNING AND IMPORTANT LABEL PLACEMENT WARNING Before starting an exercise program consult a physician. If you feel unusual pain, diziness, shortness of breath, chest tightness or discomfort, stop all use and consult your physician immediately. Manufactured Under Patents / Misuse or abuse of this equipment may Patents Pending As Follows: lead to serious injury or death. -
Page 6: Hardware Pack
Hardware Pack STEP1 Lock Washer φ8mm （ 8 ） Cap head socket Bolt M8*20mm （ 8 ） Carriage Bolt M8*70mm （ 4 ） Cap Nut M8(3) φ8mm （ 8 ） Flat Washer Curved Washer φ8 （ 4 ） Child Safety Hook(1) STEP2 Flat Head Socket Bolt Curved Washer φ8 （... -
Page 7: Assembly Instructions
ASSEMBLY INSTRUCTIONS Step 1: Frame Stabilizer Assembly Styrofoam This is a protective packaging tube, which is disposable. 34 29 31 32 17 29 34 34 29 21 23 3pcs 4pcs 8pcs (21) (26) (34) 4pcs 8pcs 8pcs 1pcs(41) (17) (23) (29) Required Hardware: STEP 1 Required Parts:... - Page 8 NOTE: Tip the unit over onto its side on the foam blocks, as shown in Step 1 Figure. C.) In order to attach the Rear (87) and Front (85) sections of the ST3, you will need to slide the front section onto the rear section of frame, and slide the two frame pieces together.
- Page 9 Step 2: Swing Arm Assembly 18A 29 12pcs 2pcs (43) (18A) 2pcs 12pcs 12pcs (44) (23) (29) Required Hardware: STEP 2 Required Parts: • 2x (44) Aluminum End Cap • (106) Swing Arm Assembly R • 12x (18A) M8 x 16 Hex Bolt •...
- Page 10 Installing Swing Arms (See Step 2 Figure) A.) Slide Swing Arm Assembly R (106) over the pivot shaft of main frame, as shown in Step 2. NOTE: Lift spacer between bearings to allow insertion. B.) Attach using: • 1x (44) Aluminum End Cap •...
- Page 11 Handle Assembly (See Step 2 Figure) WHEN ASSEMBLING, CAREFULLY ALIGN THE GROOVE ON THE HANDRAIL WITH CONVEX PARTS ON THE PLASTIC BUSHING IN TUBE ASSEMBLY (REFER A & B IN STEP 2 FIGURE) A.) Loosen the right handle adjustment knob 2-3 turns. This will allow the arm to slide in. B.) Slide the Right Handlebar Assembly (13) into the Swing Arm Assembly R (106).
- Page 12 Step 3: Assembling the Seat Back & Seat (See Step 3 Figure) Seat Slider Assembly 1pcs 5pcs 4pcs 1pcs (28) (17) (34) (39) 4pcs 1pcs 4pcs 1pcs 1pcs (35) (99) (29) (30) (40) Required Hardware: STEP 3 Required Parts: • 5x (17) Flat Washer •...
- Page 13 Installing Seat Back Assembly (See Step 3 Figure) Assemble Seatback Assembly (52) onto the Seat Slider Assembly. Align with the lower hole and secure using provided wrench, make sure seatback rotates properly: Insert the Fixed Pin (20) into the hole on Seat Slider Assembly: •...
-
Page 14: Final Steps
Attaching the Console (Continued) D.) Connect the Power (C1) and Data (D1) cables for the console. • Put C1 into C, D1 into D (tighten round nuts at the same time) As seen in Step 3 Figure and in figure to the right. FINAL STEP Level the unit by adjusting the leveling feet under both the front and rear stabilizer. -
Page 15: Product Features
Secure using the Locking Pin (20) attached to the unit. Child Safety Lock Safety is a primary concern at Inspire and that is why we suggest engaging the Child Safety Lock feature whenever your workout is completed. Permanently tethered to the left side of the front stabilizer is a hook that will latch to the left pedal/handlebar assembly. -
Page 16: Parts List
PARTS LIST Description Spec Qty. RC805-401-001 Seat Pad RC805-401-002 Backrest Pad RC805220001HJ Tablet Holder tube RC805340001PZ Rear Stabilizer Tube RC805340002PZ Front Stabilizer Tube RC803-300-001 Swing Arm Tube, Left RC803-300-002 Swing Arm Tube, Right RC805-630-001 10" tablet RC805-881-001 Cover φ13.6*8 RC804-561-030 Bushing RC805360001HJ Backrest Tube... - Page 17 Description Spec Qty. 0171-222-004C Bearing 2204-2RS RC804-320-001 Pedal Arm Tube φ45 RC804-881-001 Stopper M4*16 0113-104-168A Pan Head Screw δ1.5 RC803-201-004 Power Input Receptacle RC804-801-002B Main Shroud, Right Cross Head Bolt M4*10 M4*10 0113-104-108 RC804-801-008A Crank Cover RC804-240-001 Crank Hex Nut M20*1.0 M20*1.0 RC800-391-012 Ø25*Ø20*7...
- Page 18 ALTERNATE ADAPTER CABLE OPTIONS (TO BE ORDERED SEPARATELY) Part Number Countries Type Photo United States, Japan, Phillipines, Canada, Columbia, Ecuador, A-type RC802-631-002 Honduras, Mexico, Panama, Peru, Taiwan I-type RC802-631-003 Australia, New Zealand, China Europe, Argentina, Russia, Brazil, Egypt, India, Indonesia, Israel, C-type RC802-631-004 Pakistan, South Korea, South Africa...
-
Page 19: Exploded View 1
EXPLODED VIEW 1 exp1 28 1 17 29 34 35 42 23 STEP1 Lock Washer φ8mm （ 8 ） Cap head socket Bolt M8*20mm （ 8 ） Carriage Bolt M8*70mm （ 4 ） Flat Washer φ8mm （ 8 ） Cap Nut M8(4) Curved Washer φ8 （... -
Page 20: Exploded View 2
EXPLODED VIEW 2 exp2 81 82 66 94 93 92 91 46 90 89 88 79 18 74 Pg. 20 V12092021... -
Page 21: Warranty
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This is the only express warranty applicable to Health In Motion’s “Inspire” branded strength products. - Page 22 Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 23 V12092021...