Related Manuals for Enfora Enabler IIG
Summary of Contents for Enfora Enabler IIG
- Page 1 Transition Guide: EDG0108TG001 Enfora Enabler IIG To Enabler II-E Modem Transition Guide Rev. 1.00...
- Page 2 Enfora, Inc. customers using, integrating, and/or selling this product for use in such applications do so at their own risk and agree to fully indemnify Enfora, Inc. for any damages resulting from illegal use or resale.
-
Page 3: Table Of Contents
Enabler II-E EMC/Safety Requirements for the Countries of the European Union (EU) ........12 Enabler II-E Assembly Requirements ........................12 RF P ..........................13 OWER PECIFICATIONS SOFTWARE CHANGES ..........................14 ............................. 14 OMMANDS ............................. 14 HANGED OMMANDS ....................... 14 OMMANDS URRENTLY IN TABLES AND FIGURES..........................15 CONTACTING ENFORA ..........................15... -
Page 4: Manual Overview
Ver. 1.00 Manual Overview This document describes the differences between the Enfora Enabler II-G triple and quad band (GSM0107 and GSM0108) modems as they compare to the Enfora Enabler II-E EDGE (EDG0108) modem. This document describes the hardware interface differences between the platforms as to streamline the process of migrating solutions to the Enabler II-E EDGE technology. -
Page 5: Introduction
Introduction 2.1 General Comments If you are integrating the GSM0107 or GSM0108 for the first time, please refer to the Enfora Enabler II-G Triple-Band Radio Modem Integration Guide GSM0107IG001 or Enfora Enabler II-G Quad-Band Radio Integration Guide GSM0108IG001 documents respectively. If you are integrating the EDG0108 for the first time, please refer to the document Enfora Enabler II-E Quad-Band Integration Guide EDG0108IG003. - Page 6 Transition Guide Ver. 1.00 Figure 1 - EDG0108 Mechanical – without SIM carrier EDG0100TG001 Page 3 Rev. 1.00 – 11/03/2005...
- Page 7 Transition Guide Ver. 1.00 Figure 2 - EDG0108 Mechanical - with SIM carrier EDG0100TG001 Page 4 Rev. 1.00 – 11/03/2005...
- Page 8 Transition Guide Ver. 1.00 Figure 3 - GSM0107/GSM0108 Mechanical – without SIM carrier Figure 4 - GSM0107/GSM0108 Mechanical - with SIM carrier EDG0100TG001 Page 5 Rev. 1.00 – 11/03/2005...
- Page 9 Transition Guide Ver. 1.00 EDG0100TG001 Page 6 Rev. 1.00 – 11/03/2005...
-
Page 10: Mounting Differences
Transition Guide Ver. 1.00 2.1.3 Mounting Differences The mounting hole that existed on the GSM0107/GSM0108 is no longer present on the EDG0108. The solder tab positions on the EDG0108 are backward compatible with the GSM0107/GSM0108. 2.1.4 Interface Pin-out Differences The following table provides differences between the existing GSM0107/0108 modules and the new EDG0108 platform. - Page 11 Transition Guide Ver. 1.00 GSM0107/0108 EDG0108 Name Description Name Description DSR_RADIO DSR to Host DSR_RADIO DSR to Host ADC2 A to D Input ADC2 A to D Input DCD to Host DCD to Host SIM_CLK SIM Clock SIM_CLK SIM Clock Ring Indicator Ring Indicator Ground...
-
Page 12: Electrical Changes
Transition Guide Ver. 1.00 Electrical Changes 3.1 PIN 22 Changes On GSM0107/0108, the High = Module Run PWRDN_RADIO input controlled an Radio Power Down/ GSM0107/0108 Float = Module Run internal power switch that physically Remote ON Low = Module OFF disconnected power to a majority of the module. - Page 13 Transition Guide Ver. 1.00 J208 SW204 SW203 SW201 Figure 5 - SDK0107 Block Diagram There are two ways to control the power sequence using the combination of the development board and the module. The first method is to place SW203 in the OFF position. Apply power to the SDK and the module will turn on and off with SW201.
-
Page 14: Regulation And Compliance Differences
TS 51.010-1. For applications that use an unmodified version of the Enfora Enabler II-E module, further testing in this area may not be required. Any OEM changes in the SIM interface, antenna port, software or the physical makeup of the unit may require an incremental delta FTA to ensure continued compliance with the above-mentioned standard. -
Page 15: Enabler Ii-G Emc/Safety Requirements For The Countries Of The European Union (Eu)
Transition Guide Ver. 1.00 Enabler II-G EMC/Safety Requirements for the Countries of the European Union (EU) The European Union (EU) is comprised of fifteen countries that follow a harmonized set of standards, utilizing the CE mark as a uniform mark of acceptance. The member countries are: •... -
Page 16: Rf Power Specifications
Transition Guide Ver. 1.00 3.5 RF Power Specifications Note that the RF power specifications are not the same. Refer to the EDG0108PB003MAN for the latest specifications. EDG0100TG001 Page 13 Rev. 1.00 – 11/03/2005... -
Page 17: Software Changes
Transition Guide Ver. 1.00 Software Changes 4.1 New Commands +CGDSCONT – Define Secondary PDP Context +CGEQREQ – 3G Quality of Service Profile (Request) +CGEQMIN - 3G Quality of Service Profile +CGEQNEG – 3G Quality of Service Profile +CGCMOD – PDP Context Modify +CGTFT –... -
Page 18: Tables And Figures
Figure 3 - GSM0107/GSM0108 Mechanical – without SIM carrier..............5 Figure 4 - GSM0107/GSM0108 Mechanical - with SIM carrier ............... 5 Figure 5 - SDK0107 Block Diagram .......................10 Contacting Enfora Please use the following contact information for customer or technical support questions. Customer Support http://www.enfora.com/support...