Subscribe to Our Youtube Channel
Related Manuals for Mountup MU0024
Summary of Contents for Mountup MU0024
- Page 1 Dual Monitor Counterbalance Desk Mount Instruction Manual 75x75 MU0024 32" 100x100 (1.5~8kg)x2 (3.3~17.6lbs)x2 If you have any questions , please contact us. V3.0...
-
Page 2: Package Contents
WARNING! If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us. Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or serious injury. -
Page 3: Assembly Steps
ASSEMBLY STEPS STEP 1: Choose a mounting option OPTION A: Clamp Installation Mount clamp base support (C) to monitor stand (A) with Bolts (J). Bolts could be tightened by the 4mm Allen Key (M), then Apply pads (L) to the monitor stand (A) bottom to avoid desk scratches. Attach Clamp (D) to clamp base support (C) with Bolts (J) and 4mm Allen Key (M). - Page 4 STEP 1: (Continued) OPTION B: Grommet Base Installation Place long screw (F) through the center of base support (G). Mount grommet base to monitor stand (A) Bottom with Bolts (J) and tighten by 4mm allen key (M). Apply pads (L) to the monitor stand (A) bottom to avoid desk scratches. Run long screw (F) through grommet hole on desktop.
- Page 5 STEP 2: Attach the monitors to the arm OPTION A: Flat Back Monitor Attach the VESA plate (B) to back of monitor and secure with screws (M-A) or (M-C) with washers (M-E) using 6mm Allen key(N). Do not tighten the screws excessively or your monitor might be damaged.
- Page 6 STEP 3: Hang Monitor Slide the monitor onto the head of swivel arm, install the security screw (I). Make sure the security screw is installed before you rotate the monitor. Important Notice: The gas spring tension is pre-set to the weakest level by default, please hold your monitor by both hands and do not let go so soon after the VESA plate is attached to the swivel arm.
-
Page 7: Step 4: Adjust The Tension
STEP 4: Adjust the tension For proper functioning of this mount, depending on di erent weight of monitor you might need to adjust tension in upper arm using 6 mm allen key (N). CAUTION Note1: Be sure to keep the arm in horizontal position during adjustment. After being attached to the arm, the monitor falls down and can not stay at the desired height by itself. -
Page 8: Step 5: Cable Management
STEP 5: (Continued) STEP 5: Cable Management For both bottom and upper portion of the arm, just slide the cable cover up and away from the arm, do not need to take much e ort to pull the ends of the cable cover away from the arm. - Page 9 STEP 5: (Continued) STEP 5: (Continued) On the bottom portion of the arm, insert the cable and slide the cable cover down; On the upper portion of the arm, insert the cable and press the tabs on the inside of the cable cover slightly inward and slide down to reattach the cable cover.
- Page 10 Adjust as Desired Allen key(M,N) can be stored in Base Support Cover(E) for next time using. Note: When tilted, if the monitor sags or does not stay, please fasten the tilting bolt on the mount until the monitor can be held at any angle as needed.
-
Page 11: Product Dimensions
Product Dimensions 8.7"-10.8" 6.7“ 2.4“ 180° 2.9“ 360° 3.9“ 4.5“ 360° 270° 1.97“... - Page 12 CAUTION AND MAINTENANCE: • Never allow children to climb, stand, hang, or play on any part of monitor or stand. • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. •...
Need help?
Do you have a question about the MU0024 and is the answer not in the manual?
Questions and answers