Outback Jupiter 4S Assembly And Operating Instructions Manual

Gas/charcoal hybrid

Advertisement

Quick Links

Assembly and Operating Instructions for Outback
Jupiter 4S Gas/Charcoal Hybrid and Jupirer 6S Gas/Charcoal Hybrid
RS4491SH
Photographs are not to scale.
Specifications subject to change
without prior notice.
WARNING
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open barbecue lid or hood.
4. If odour continues, discontinue use and contact
your local dealer.
For outdoor use only. Not for commercial use.
Read instructions before using the appliance. Failure to follow instructions could
result in death, serious bodily injury, and/or property loss.
Warning: accessible parts may be very hot. Keep young children and pets away.
Do not move the appliance during use.
Turn off the gas supply at the gas bottle after use.
Any modification of the appliance, misuse, or failure to follow the instructions
may be dangerous and will invalidate your warranty. This does not affect your
statutory rights.
Retain these instructions for future reference.
Leak test annually, and whenever the gas bottle is removed or replaced. Check
that the hose connections are tight and leak test each time you reconnect the gas
bottle.
For Flare-up control please refer to the 'OPERATION' section of this manual.
FOR YOUR SAFETY
1. Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2. A gas bottle not connected for use shall not be
stored in the vicinity of this or any other
appliance.
®
RS5691SH
2575
0359

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Jupiter 4S and is the answer not in the manual?

Questions and answers

Summary of Contents for Outback Jupiter 4S

  • Page 1 ® Assembly and Operating Instructions for Outback Jupiter 4S Gas/Charcoal Hybrid and Jupirer 6S Gas/Charcoal Hybrid RS4491SH RS5691SH Photographs are not to scale. Specifications subject to change 2575 0359 without prior notice.  For outdoor use only. Not for commercial use.
  • Page 2: Parts List

    Parts List Quantity varies according to model purchased. Specifications subject to change without prior notice. For more details on hardware, please see the corresponding ‗Hardware Reference Diagram‘. Jupiter 4S Gas/ Jupiter 6S Gas/ CODE PART Charcoal Hybrid Charcoal Hybrid Hood (Pre-Assembled to Body) ...
  • Page 3: Parts Diagram

    Parts Diagram Quantity varies according to model purchased. Specifications subject to change without prior notice. For more details on hardware, please see the corresponding ‗Hardware Reference Diagram‘.
  • Page 4 Hardware Reference Diagram Specifications subject to change without prior notice.
  • Page 5 Assembly IMPORTANT! TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/Crosspoint screwdriver,  adjustable spanner or metric spanner set. Remove any internal component or packaging from the barbecue body.  Whilst every care is taken in the manufacture of this product, care must be taken during assembly in ...
  • Page 6 Attach the Food Basket Brackets (C25x2pcs) onto the Middle Panel (C24) using M6x15 Bolts (D2x4pcs), and then attach the middle panel assembly to the cabinet assembly using M6x15 Bolts (D2x5pcs) as shown. Attach the Upper Support (C16) to the left/right cabinet panel assembly using M6x15 Bolts (D2x4pcs).
  • Page 7 Attach the Front Wheel Skirt (C22) onto the bottom panel using M6x15 Bolts (D2x3pcs) as shown. Carefully turn the cabinet upside-down. Attach the Casters (C28x2pcs) and Lockable Casters (C27x2pcs) onto the left/right cabinet panels as shown. Ensure the lockable casters are installed on the rear side.
  • Page 8 Remove the retaining bolts from one Door Handle (C17), then attach the door handle onto the Left Door (C18) using the retaining bolts as shown. Repeat above process for Right Door (C19). Fit the doors to the cabinet by depressing the spring pins and placing into the cabinet.
  • Page 9 Carefully place the Barbecue Body (B1) onto the cabinet assembly and fix it using M6x15 Bolts (D2x4pcs) as shown. Attach Side Shelf Panel (C4) onto Side Shelf (C3) using M6x15 Bolts (D2x2pcs) and M6 Nut (D6x2pcs) as shown.
  • Page 10 step1 step2 step3 step4 Attach the side shelf assembly to the barbecue body using ST4.0x10 Screw (D5x2pcs) and M6x15 Bolts (D2x4pcs) as shown. Attach Side Burner Shelf Panel (C2) onto Side Burner Shelf (C1) using M6x15 Bolts (D2x2pcs) and M6 Nut (D6x2pcs) as shown.
  • Page 11 step1 step2 step4 step3 Attach the side burner shelf assembly to the barbecue body using ST4.0x10 Screw (D5x2pcs) and M6x15 Bolts (D2x4pcs) as shown. Attach the Side Burner Firebox (C8) into the side burner shelf using M4x10 Bolts (D7x4pcs) as shown.
  • Page 12 Attach the side burner valve and Knob Bezel (C10) onto side burner shelf using M4x10 Bolts (D7x2pcs) as shown. Press the Side Burner Knob (C11) onto side burner valve stem. Insert the wire of the Side Burner Electrode (C9) through the side burner firebox as shown; and then fix the side burner electrode onto side burner firebox using a ST4.0x10 F# Screw (D3).
  • Page 13  Feed the tube of the Sear Burner (C12) through the guide hole in the side burner firebox, and fix it using M5x15 Bolt (D4x2pcs) as shown. Make sure that the end of tube is set over the gas outlet of side burner valve. Attach Side Burner Lid (C6) onto the side burner shelf using Side Burner Lid Axle (C7) as shown.
  • Page 14 Place the Side Burner Grid (C5) onto the side burner shelf. NOTE: Only use cookware with a base diameter of between 150mm and 220mm on the side burner. Insert the Side Burner Drip Tray (C13) by sliding it underneath the side burner frame as shown.
  • Page 15 Insert the Drip Tray (B9) by sliding it underneath the barbecue body. Jupiter 4S Jupiter 6S Lay the Flame Tamers (B6) carefully into the body ensuring it lies level within the body. Lay the Cooking Grills (B8) and Round Grill (B7) into place. Place the Chopping Board...
  • Page 16 Attach the Warming Rack (A3) to the barbecue body as shown. Insert the Hook Rail (C30) through the Tool Hooks (C29) as shown, then fix the assembly onto side shelf panel using M5x10 Bolts (D8x2pcs).
  • Page 17 Attach the Food Baskets (C26x2pcs) by placing them on the brackets as shown. Lay the Clapboard (C23) on the brackets inside of cabinet and slide it to the end as shown.
  • Page 18: Leak Testing

    1. Maximum diameter or breadth is 320mm. 2. Maximum height (regulator included) is 700mm. ASSEMBLY IS NOW COMPLETE. PROCEED TO THE NEXT PAGE FOR INSTRUCTIONS ON OPERATION AND MAINTENANCE ALL JOINTS AND CONNECTIONS MUST NOW BE LEAK TESTED BEFORE USING THE BARBECUE.
  • Page 19: Gas, Regulator And Hose

    Important Information  Before you use your barbecue, perform a leak test. This is the only safe and sure way Please read these instructions carefully to detect any gas leaking from joints and before assembly and use of your barbecue. connections of the barbecue after assembly.
  • Page 20: Installation

    BOTTLE IN ORDER FOR THE BARBECUE TO Operation OPERATE SAFELY AND EFFICIENTLY. USE INCORRECT FAULTY Warnings REGULATOR BOTTLE  Before proceeding, make certain that you DANGEROUS AND WILL INVALIDATE ANY understand IMPORTANT WARRANTY. In the case of replacing your INFORMATION section of this manual. original hose and regulator, please consult your ...
  • Page 21 should be open during preheating. cooking items that require high-temperature/  After completion of preheating, turn all short-duration cooking, such as vegetables and smaller cuts of fish. Similarly, it can be used in burners to the low position for best cooking exactly the same way as a griddle in the results.
  • Page 22: Care And Maintenance

    to prevent food being burned. To control flare- Turning Off Your Barbecue ups, it is ABSOLUTELY ESSENTIAL to trim When you have finished using your barbecue, away excess fat from meat and poultry before turn all the control valves fully clockwise to the grilling, use cooking sauces and marinades ―Off‖...
  • Page 23 cleaning in a dishwasher. refitting into body. A stainless steel cleaner may be used on Burner stainless steel parts if required. Provided that they are operating correctly, in normal usage, burning off the residue after Barbecue Hood or Lid & Trolley cooking will keep the burners clean.
  • Page 24: Technical Specifications

    Technical Specifications NOTES: Heat Injector Burners Input Size Consumption Outback® Butane: 943g/hr Jupiter 4S Gas/ 12.96kW 0.89mm Propane: 926g/hr Charcoal Hybrid Outback® Butane: 1415g/hr Jupiter 6S Gas/ 19.44kW 0.89mm Propane: 1390g/hr Charcoal Hybrid Butane: 328g/hr Side Burner 4.5kW 1.04mm Propane: 322g/hr...
  • Page 25: Troubleshooting

    Troubleshooting Problem Possible Cause Solution Burner will not light using LP gas bottle is empty Replace with full bottle the ignition system Faulty regulator Have regulator checked or replaced Obstructions in burner Clean burner Obstructions in gas jets or gas hose Clean jets and gas hose Electrode wire is loose is connected on Reconnect wire...
  • Page 26 The product has not sustained damage through foreign objects, substances or accidents.  The care and maintenance instructions given in your Outback manual have been followed.  If the product includes one or a number of parts or accessories, only the defective accessory or part will be replaced i.e.

This manual is also suitable for:

Jupiter 6sRs4491shRs5691sh

Table of Contents