Advertisement
Quick Links
Advertisement
Related Manuals for KTM 1290 Super Adventure R EU 2019
Summary of Contents for KTM 1290 Super Adventure R EU 2019
- Page 1 SETUP INSTRUCTIONS 2019 1290 Super Adventure R Art. no. 3213979en...
- Page 3 KTM accepts no liability for delivery options, deviations from figures and descriptions, misprints, and other errors. The models portrayed partly contain special equipment that does not belong to the regular scope of supply.
-
Page 4: Means Of Representation
1 MEANS OF REPRESENTATION Symbols used The meaning of specific symbols is described below. Indicates an expected reaction (e.g. of a work step or a function). Indicates an unexpected reaction (e.g. of a work step or a function). Indicates a page reference (more information is provided on the specified page). Indicates information with more details or tips. - Page 5 To operate the vehicle, the vehicle electronics must be enabled. This process is conducted during initial setup in KTM Dealer.net. Enabling ensures that the initial setup in KTM Dealer.net is docu- mented. Enabling can be performed either temporarily, e.g. for a test ride, or permanently for vehicle handover.
- Page 6 2 SETUP – Remove the controls from the transport holder. – Remove the screws and handlebar clamps. – Remove the transport holder. F01005-01 – Remove the right hand guard. – Position the controls on the right half of the handlebar. Tighten the screws.
- Page 7 SETUP 2 – Mount and tighten the rear mirror on both sides. F01345-01 – Mount rear reflector with spring washers on holding plate – Mount the retaining plate on the license plate holder. (all EU/JP/CN models) – Mount the license plate holder. (US) –...
- Page 8 2 SETUP – Mount damping rubber pieces on the engine guard. – Position the engine guard. Mount and tighten the screws with the distance sleeves. Guideline Screw, engine guard 10 Nm (7.4 lbf ft) F00998-10 – Mount the frame protector elements on both sides.
- Page 9 Mount locking plate and nut – Tighten nut – Repeat these steps on the opposite side. F01009-01 Condition Function KTM MY RIDE (optional) activated. – Remove screws – Take off the headlight mask. F01006-10 – Remove screws with the sleeves.
- Page 10 Info If the function KTM MY RIDE is enabled, the sticker must be applied. If the function KTM MY RIDE is not enabled or has been disabled, the sticker must not be applied. – Plug in connector H02004-10 –...
- Page 11 SETUP 2 – Prepare the vehicle according to the specifications in the KTM Dealer.net for handover to the customer.
- Page 12 3 WORK Installing the windshield – Position windshield – Mount and tighten screws with the rubber bushings. Guideline Screw, wind shield 3.5 Nm (2.58 lbf ft) K00846-11 Removing the seat – Insert the Race‑on key or the black ignition key into the seat lock and turn clockwise.
- Page 13 WORK 3 Note Environmental hazard 12 V batteries contain environmentally hazardous materials. – Do not dispose of 12 V batteries as household waste. – Dispose of 12 V batteries at a collection point for used batteries. Note Environmental hazard Hazardous substances cause environmental damage. –...
- Page 14 3 WORK Guideline The charging current, charging voltage, and charging time must not be exceeded. Recharge the 12-V battery 3 months regularly when the motorcy- cle is not being used Finishing work – Install the 12-V battery. ( p. 13) –...
- Page 15 WORK 3 – Disconnect both negative cables from the 12-V battery. – Disconnect both positive cables from the 12-V battery. – Take the 12-V battery and battery case out of the battery compartment. M00610-10 Installing the 12-V battery Warning Risk of injury Battery acid and battery gases cause serious chemical burns. –...
- Page 16 3 WORK – Close cover and gently push down. The cover engages with an audible click. S02275-10 Finishing work – Mount the seat. ( p. 10) – Set the time and date. Setting the time and date Condition The motorcycle is stationary. –...
- Page 17 WORK 3 The day next to Date flashes. – Press the UP or DOWN button until the current day is set. – Press the SET button. The year next to Date flashes. – Press the UP or DOWN button until the current year is set. –...
- Page 18 3 WORK – Set the headlight to marking Guideline The light-dark boundary must lie exactly on lower mark- when the motorcycle is ready to operate with the rider mounted along with any luggage and a passenger if applicable. 400726-11 3.10 Starting Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and death.
- Page 19 WORK 3 – Shift the transmission into neutral The green idle indicator lamp lights up. – Turn the emergency OFF switch/electric starter button to the lower position Info Do not press the emergency off switch/electric starter button into the lower position until the combination instrument function check has been completed.
- Page 20 3 WORK – Fold up cover slowly. The fuel tank filler cap is unlocked. – Fold up fuel tank filler cap K00826-10 3.12 Closing the fuel tank filler cap Warning Fire hazard Fuel is highly flammable, toxic and a health hazard. –...
- Page 21 WORK 3 Note Environmental hazard Improper handling of fuel is a danger to the environment. – Do not allow fuel to enter the groundwater, the soil, or the sewage system. – Switch off the engine. – Open the fuel tank filler cap. ( p.
-
Page 22: Technical Data
4 TECHNICAL DATA Chassis tightening torques Nut, tire pressure sensor (All ISO 10V2 12 Nm (8.9 lbf ft) Loctite ® 2701™ EU/US/CN models) Nut, valve (JP) ISO 10V2 12 Nm (8.9 lbf ft) Loctite ® 2701™ Screw, combination switch, left 5 Nm (3.7 lbf ft) Screw, headlight EJOT ALtracs... - Page 23 TECHNICAL DATA 4 Screw, cover part 6 Nm (4.4 lbf ft) Screw, engine guard 10 Nm (7.4 lbf ft) Screw, exhaust clamp 8 Nm (5.9 lbf ft) Screw, foot brake cylinder 10 Nm (7.4 lbf ft) Loctite ® 243™ Screw, front brake disc 14 Nm (10.3 lbf ft) Loctite 243™...
- Page 24 4 TECHNICAL DATA Screw, handlebar support 40 Nm (29.5 lbf ft) Loctite ® 243™ Screw, side stand 35 Nm (25.8 lbf ft) Loctite ® 243™ Screw, side stand bracket 45 Nm (33.2 lbf ft) Loctite ® 243™ Banjo bolt, brake line M10x1 25 Nm (18.4 lbf ft) Nut, rear sprocket screw...
- Page 25 SUBSTANCES 5 Super unleaded (ROZ 95/RON 95/PON 91) Standard/classification – DIN EN 228 (ROZ 95/RON 95/PON 91) Guideline – Only use unleaded super fuel that matches or is equivalent to the specified fuel grade. – Fuel with an ethanol content of up to 10 % (E10 fuel) is safe to use. Info Do not use fuel containing methanol (e.
- Page 26 *3213979en* 3213979en 08/2018 KTM Sportmotorcycle GmbH 5230 Mattighofen/Austria Photo: Mitterbauer/KTM http://www.ktm.com...