Advertisement
Quick Links
Advertisement
Related Manuals for KTM 1290 Super Adventure R EU 2018
Summary of Contents for KTM 1290 Super Adventure R EU 2018
- Page 1 SETUP INSTRUCTIONS 2018 1290 Super Adventure R Art. no. 3213793en...
- Page 3 KTM accepts no liability for delivery options, deviations from illustrations and descrip- tions, misprints, and other errors. The models portrayed partly contain special equipment that does not belong to the regular scope of supply.
-
Page 4: Means Of Representation
1 MEANS OF REPRESENTATION Symbols used The meaning of specific symbols is described below. Indicates an expected reaction (e.g. of a work step or a function). Indicates an unexpected reaction (e.g. of a work step or a function). Indicates a page reference (more information is provided on the specified page). Indicates information with more details or tips. - Page 5 SETUP 2 Unpacking and setting up the vehicle – Remove the straps and box. F01344-10 – Remove the adhesive tape in the upper area of the motorcycle. F01003-01 – Roll down the film at the sides. Info To avoid damaging the motorcycle during unpacking, leave the other films on the vehicle until you have fin- ished work on the vehicle.
- Page 6 2 SETUP Warning Danger of accidents A repaired handlebar poses a safety risk. If the handlebar is bent or straightened, the mate- rial becomes fatigued. The handlebar may break as a result. – Change the handlebar if the handlebar is damaged F00996-10 or bent.
- Page 7 SETUP 2 – Mount reflector with spring washers on holding plate – Mount the holding plate on the license plate bracket. (all EU/JP/CN models) – Mount the license plate holder. (US) – Bond the reflectors on the right and left side of the reflec- tor holder.
- Page 8 2 SETUP – Mount the frame protector elements on both sides. – Position the left crash bar with frame protector and attach the clamp to the frame tube. Info Cover the components to protect them against damage. – Mount screw but do not tighten yet.
- Page 9 Mount locking plate and nut – Tighten nut – Repeat these steps on the opposite side. F01009-01 Condition Function KTM MY RIDE (optional) activated. – Remove screws – Take off the headlight mask. F01006-10 – Remove screws with the sleeves.
- Page 10 Info If the function KTM MY RIDE is enabled, the sticker must be applied. If the function KTM MY RIDE is not enabled or has been disabled, the sticker must not be applied. – Plug in connector H02004-10 –...
- Page 11 WORK 3 Installing the wind shield – Position wind shield – Mount and tighten screws Guideline Screw, wind shield 3.5 Nm (2.58 lbf ft) K00846-11 Removing the seat – Insert the Race‑on key or the black ignition key into the seat lock and turn clockwise.
- Page 12 3 WORK Warning Environmental hazard Batteries contain environmentally-hazardous materials. – Do not dispose of batteries as household waste. – Dispose of batteries at a collection point for used batteries. Warning Environmental hazard Hazardous substances cause environmental damage. – Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable regulations.
- Page 13 WORK 3 Finishing work – Install the battery. ( p. 12) – Mount the seat. ( p. 9) – Set the time and date. Removing the battery Warning Risk of injury Battery acid and battery gases cause serious chemical burns. – Keep batteries out of the reach of children.
- Page 14 3 WORK Installing the battery Warning Risk of injury Battery acid and battery gases cause serious chemical burns. – Keep batteries out of the reach of children. – Wear suitable protective clothing and safety glasses. – Avoid contact with battery acid and battery gases. –...
- Page 15 WORK 3 Setting the time and date Condition The motorcycle is stationary. – Press the SET button when the menu is closed. – Press the UP or DOWN button until Preferences appears. Press the SET button to open the menu. –...
- Page 16 3 WORK Checking the headlight setting – Park the vehicle on a horizontal surface in front of a light- colored wall and make a mark at the height of the center of the low beam headlight. – Make another mark at a distance under the first marking.
- Page 17 WORK 3 3.10 Starting Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and death. – Always make sure there is sufficient ventilation when running the engine. – Use an effective exhaust extraction system when starting or running the engine in an enclosed space. Caution Danger of accidents Electronic components and safety devices will be damaged if the battery is discharged or missing.
- Page 18 3 WORK – Turn the emergency OFF switch/electric starter button to the lower position Info Do not press the emergency off switch/electric starter button into the lower position until the combination instrument function check has been completed. When starting, DO NOT open the throttle. If you open the throttle during the starting procedure, fuel is not injected by the engine management system and the F00908-01...
- Page 19 WORK 3 – Fold up cover slowly. The filler cap unlocks. – Fold open filler cap K00826-10 3.12 Closing the filler cap Warning Fire hazard Fuel is highly flammable, toxic and a health hazard. – Check the filler cap is locked correctly after clos- ing.
- Page 20 3 WORK Warning Environmental hazard Improper handling of fuel is a danger to the environment. – Do not allow fuel to enter the groundwater, the soil, or the sewage system. – Switch off the engine. – Open the filler cap. ( p.
-
Page 21: Technical Data
TECHNICAL DATA 4 Chassis tightening torques Nut, tire pressure sensor (All ISO 10V2 12 Nm (8.9 lbf ft) Loctite ® 2701™ EU/US/CN models) Nut, valve (JP) ISO 10V2 12 Nm (8.9 lbf ft) Loctite ® 2701™ Screw, combination switch, left 5 Nm (3.7 lbf ft) Screw, headlight EJOT ALtracs... - Page 22 4 TECHNICAL DATA Screw, foot brake cylinder 10 Nm (7.4 lbf ft) Loctite ® 243™ Screw, front brake disc 14 Nm (10.3 lbf ft) Loctite ® 243™ Screw, front wheel speed sensor 10 Nm (7.4 lbf ft) Screw, fuel pump 6 Nm (4.4 lbf ft) Screw, fuel tank 10 Nm (7.4 lbf ft)
- Page 23 TECHNICAL DATA 4 Screw, side stand bracket 45 Nm (33.2 lbf ft) Loctite ® 243™ Banjo bolt, brake line M10x1 25 Nm (18.4 lbf ft) Nut, rear sprocket screw M10x1.25 50 Nm (36.9 lbf ft) Loctite ® 243™ Lambda sensor M12x1.25 25 Nm (18.4 lbf ft) Screw, bottom shock absorber...
- Page 24 5 SUBSTANCES Super unleaded (ROZ 95/RON 95/PON 91) Standard/classification – DIN EN 228 (ROZ 95/RON 95/PON 91) Guideline – Only use unleaded super fuel that matches or is equivalent to the specified fuel grade. – Fuel with an ethanol content of up to 10 % (E10 fuel) is safe to use. Info Do not use fuel containing methanol (e.
- Page 25 *3213793en* 3213793en 11/2017 KTM Sportmotorcycle GmbH 5230 Mattighofen/Austria Photo: Mitterbauer/KTM http://www.ktm.com...