Deltech Fitness DF4900 Assembly Manual
  1. Manuals
  2. Brands
  3. Deltech Fitness Manuals
  4. Fitness Equipment
  5. DF4900
  6. Assembly manual

Deltech Fitness DF4900 Assembly Manual

Linear bearing smith machine
Hide thumbs Also See for DF4900:
Table of Contents

Advertisement

Quick Links

Download this manual
DF4900
LINEAR BEARING
SMITH MACHINE
Assembly Manual
Assembly Video Available
Simply scan the QR code below
on your phone's camera to access
the video
(888) 258-0533
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533

Advertisement

Table of Contents
loading

Related Manuals for Deltech Fitness DF4900

Summary of Contents for Deltech Fitness DF4900

  • Page 1 Simply scan the QR code below on your phone’s camera to access the video (888) 258-0533 FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533...
  • Page 2 LH FOOT RH FOOT CROSSMEMBER TOP FRAME QTY 1 QTY 1 QTY 1 QTY 1 WEIGHT PLATE HOLDER QTY 4 *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533...
  • Page 3 LH & RH SAFETY CATCH LH & RH GUIDE ROD COLLAR SMITH BAR COLLARS QTY 1 EACH QTY 1 EACH QTY 2 *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533...
  • Page 4 QTY 8 QTY 20 QTY 40 QTY 16 CHROME SPRING HEX WRENCH CORNER FLANGE QTY 2 QTY 2 QTY 2 *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533...

  • Page 5: Frame Assembly

    TOOLS REQUIRED: WRENCHES OR METRIC SOCKET SET HEX WRENCHES (INCLUDED) ASSEMBLY REQUIRES 2 PEOPLE MAKE SURE GUIDE BAR RETAINERS ARE TOWARDS THE OUTSIDE (NOTE: THE NUTS USED ON THIS PRODUCT ARE LOCK NUTS, THIS MEANS YOU MUST TIGHTEN THEM DOWN PAST THE PLASTIC INSERT) ASSEMBLE THE LH FOOT (E), RH FOOT (F), CROSS MEMBER (G), AND THE LEFT AND RIGHT REAR SUPPORTS (C) AND (D), USING THE M12 x 90MM BOLTS (V), M12 WASHERS (X), AND M12 LOCK-...
  • Page 6 ASSEMBLE THE LH AND RH UPRIGHTS (A) & (B) TO THE LH AND RH FEET USING THE M12 x 90MM BOLTS (V), M12 WASHERS (X), AND M12 LOCKNUTS (Z). FRAME ASSEMBLY...
  • Page 7 ASSEMBLE THE REAR SUPPORTS TO THE UPRIGHTS USING THE M12 x 90MM BOLTS (V), M12 WASHERS (X), AND M12 LOCKNUTS (Z). FRAME ASSEMBLY...
  • Page 8 INSTALL HOOK CATCH RODS INTO UPRIGHTS USING BOLT, WASHER, AND LOCK WASHER. TIGHTEN SECURELY. SMITH BAR CATCH ROD ASSEMBLY...
  • Page 9 INSTALL WEIGHT PLATE HOLDERS (I) USING M10 x 70MM BOLTS(R), M10 WASHERS (Y), AND M10 LOCKNUT (AA). SLIDE RUBBER SPACERS (Q) ONTO WEIGHT PLATE SUPPORTS. REAR WEIGHT HOLDER ASSEMBLY...
  • Page 10 ATTACH THE CORNER FLANGE (DD) TO THE REAR OF THE UPRIGHT USING THE M12 x 90MM BOLTS (V), M12 WASHERS (X), AND M12 LOCKNUTS (Z). DO NOT TIGHTEN NUTS AT THIS TIME. REPEAT FOR OPPOSITE SIDE. TOP FRAME INSTALLATION...
  • Page 11 THE FOLLOWING STEPS REQUIRE 2 PEOPLE LOWER TOP FRAME (H) ONTO UPRIGHTS. ATTACH THE TOP FRAME (H) TO THE CORNER FLANGE USING THE M12 x 90MM BOLTS (V), M12 WASHERS (X), AND M12 LOCKNUTS (Z). ONLY HAND TIGHTEN NUTS AT THIS TIME. REPEAT FOR OPPOSITE SIDE.

  • Page 12: Guide Rod Installation

    INSERT ONE GUIDE ROD (K) INTO THE RETAINER ON THE RIGHT FOOT. INSTALL THE RUBBER DONUT (S), RIGHT HAND SAFETY CATCH (O), CHROME SPRING (BB), AND RIGHT HAND GUIDE ROD COLLAR (N). BE EXTREMELY CAREFUL INSTALLING THE GUIDE ROD COLLARS AS NOT TO DAMAGE THE LINEAR BEARINGS.
  • Page 13 ROTATE THE GUIDE ROD (K) WHILE SLIGHTLY LIFTING THE TOP FRAME (H) AND INSERT TOP OF GUIDE ROD INTO RETAINER ON TOP FRAME. REPEAT THIS PROCESS FOR OPPOSITE SIDE, MAKING SURE TO HAVE SOMEONE HOLD GUIDE ROD ON RIGHT SIDE. SECURELY TIGHTEN NUTS ON CORNER FLANGES AT THIS TIME. GUIDE ROD INSTALLATION...
  • Page 14 INSERT SMITH BAR (J) BETWEEN UPRIGHTS AND GUIDE RODS. ROTATE BAR AND HANG ON HOOK CATCH RODS ON BOTH SIDES. SMITH BAR INSTALLATION...
  • Page 15 SLIDE THE SMITH BAR COLLARS (M) ONTO EACH END OF THE SMITH BAR (J) AND ALIGN MOUNTING HOLES ON SMITH BAR COLLAR (M) WITH MOUNTING HOLES ON GUIDE ROD COLLAR (N). FASTEN SMITH BAR COLLAR TO GUIDE ROD COLLAR WITH M10 x 25MM BOLTS (W), M10 WASHERS (Y), AND M10 LOCKNUTS (AA).
  • Page 16 SLIDE THE SMITH BAR COLLARS (M) ONTO EACH END OF THE SMITH BAR (J) AND ALIGN MOUNTING HOLES ON SMITH BAR COLLAR (M) WITH MOUNTING HOLES ON GUIDE ROD COLLAR (N). FASTEN SMITH BAR COLLAR TO GUIDE ROD COLLAR WITH M10 x 25MM BOLTS (W), M10 WASHERS (Y), AND M10 LOCKNUTS (AA).
  • Page 17 RAISE SMITH BAR TO THE HIGHEST SETTING AND HANG ON HOOK CATCH RODS. USE THE SUPPLIED HEX WRENCH TO ADJUST THE SET SCREWS ON EACH SIDE OF THE GUIDE ROD RETAINER. TIGHTEN EACH SIDE UNTIL THEY JUST TOUCH THE GUIDE RODS. MOVE SAFETY CATCHES AND CHROME SPRING UNTIL THEY REST ON RUBBER DONUTS.

  • Page 18: Use Instructions

    USE INSTRUCTIONS 1) SET THE SPOTTERS (9) TO THE DESIRED HEIGHT FOR A SAFE WORKOUT. 2) RAISE THE BAR AND ROTATE IT OUT UNTIL THE HOOK CLEARS THE PEGS. 3) DO EXERCISES AS DESIRED. 4) WHEN FINISHED WITH THE SET, ROTATE THE BAR BACK AND SET ON PEGS. MAKE SURE THE BAR IS SECURE BEFORE LETTING GO.

  • Page 19: Safety Notice

    SAFETY NOTICE WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS FOLLOWING THESE SIMPLE RULES: 1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.

  • Page 20: Incline Bench Press

    EXERCISES SQUAT BENCH PRESS INCLINE BENCH PRESS SHOULDER SHRUG CHIN-UP TOE RAISE...

Table of Contents