Before Using The Unit; Using The Blender Attachment - Vitek VT-3403 B Manual Instruction

ENGLISH
•
Do not disassemble and repair the unit by
yourself. If you find any damages, unplug
the unit and apply to an authorized service
center.
•
To avoid damages, transport the unit in origi-
nal package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY

BEFORE USING THE UNIT

After unit transportation or storage at low
temperature, it is necessary to keep it for at
least two hours at room temperature before
switching on.
Unpack the unit completely and remove any
–
stickers that can prevent unit operation.
Check the unit for damages; do not use it in
–
case of damages.
Before switching the unit on, make sure that
–
your home mains voltage corresponds to the
unit operating voltage.
Before using the unit, wash the removable
–
blender attachment (1), the whisk (7), the
chopper bowl (9), the chopping knife (10), the
lid (12) and the measuring cup (13) with warm
water and a neutral detergent.
Wipe the motor unit (2), the whisk gear (6)
–
and the geared lid (8) with a soft slightly damp
cloth and then wipe them dry.
Attention!
Do not immerse the motor unit (2), the whisk
gear (6), the geared lid (8), the power cord
and the power plug into water or any other
liquids.
Do not put the attachments and bowls in a
dishwashing machine.
Continuous operation time
Continuous operation time with attachments
should not exceed 1 minute. When chopping
products in the chopper bowl (9), the operation
time should not exceed 10 seconds.
Make at least a 3-5 minute break between oper-
ation cycles.

USING THE BLENDER ATTACHMENT

WARNING: Before installing the attach-
ments, make sure that the power plug is not
inserted into the mains socket.
VT-3403_IM.indd 4
Attach the detachable blender attachment
–
(1) to the motor unit (2), matching the mark
▼ on the motor unit with the mark
attachment and turn it clockwise till bumping.
The mark ▼ on the motor unit should match
the mark on the blender attachment in the
fixed position.
Insert the power plug into the mains socket.
–
Immerse the detachable blender attachment
–
(1) into the bowl with products that you want
to chop/mix. You can use the measuring cup
(13) as a bowl.
Set the required operation speed using the
–
control knob (5). To switch the unit on, press
and hold the «I» button (4). Use this operation
mode for mixing liquid products.
If you press and hold the «II» button (3), the
–
unit will operate at maximum rotation speed.
Use this operation mode for combined pro-
cessing of liquid and hard products.
Notes:
Products should be put into the bowl before
the unit is switched on. The amount of
processed products should not exceed 2/3
of the capacity of the bowl in which they are
processed.
Before you start
recommend to peel fruit, remove inedible
parts, such as stones, and to cut fruit into
cubes approximately 2х2 cm in size.
If food processing is hindered, add some
liquid.
−
After you finish using the blender, unplug
the unit and remove the detachable
blender attachment (1) by turning it so
that the mark ▼ on the motor unit (2) is
opposite the mark
Attention!
Do not remove the detachable blender
attachment (1) during operation.
To avoid damage of the blades, do not pro-
cess too hard products such as cereals, rice,
spices, coffee beans, cheese, frozen food
and ice.
When you use the blender attachment and
the products are hard to chop, add some
water, if it is possible.
USING THE WHISK
Use the whisk attachment (7) only to beat cream,
make biscuit dough or for mixing ready desserts.
4
on the
chopping/mixing, we
.
24.12.2013 10:37:48