Maxwell MW-1160 B Manual Instruction page 9

•
To avoid risk of electric shock or fire, do not immerse
the unit, the power cord and the power plug of the
unit into water or any other liquids. If the unit was
dropped into water:
–
do not touch the water;
–
unplug the unit immediately, only after that you can
take the unit out of water;
–
apply to the authorized service center for testing
and repairing the unit.
•
Keep the unit out of reach of children under 8 years
of age.
THE UNIT IS INTENDED FOR HOUSEHOLD USAGE ONLY
Before using the unit
After unit transportation or storage at low
temperature it is necessary to keep it for at least
two hours at room temperature before switching on.
•
Before using the unit, wash the blender attachment
(1), the whisk (11), the chopping knife (8), the chop-
per bowl (7) and the measuring cup (6) with warm
water and a neutral detergent.
•
Wipe the motor unit (2), whisk gear (10) and geared lid
(9) with a soft slightly damp cloth and then wipe it dry.
Attention!
•
Do not immerse the motor unit (2), the whisk gear
(10), the geared lid (9), the power cord and the
power plug into water or any other liquids.
•
Do not put the attachments and bowls in a dish-
washing machine.
Continuous operation time
•
Continuous operation time with the attachments
should not exceed 30 seconds; the weight of the
products to be chopped in the mini-chopper should
not exceed 500 g.
•
Make at least a 3-5 minute break between opera-
tion cycles.
Using the blender attachment
WARNING: Before assembling and installing the
attachments make sure that the power plug is not
inserted into the mains socket.
•
Attach the blender attachment (1) to the motor unit
(2), matching the mark  on the motor unit (2) with
the mark on the blender attachment (1) and
turn it clockwise till bumping. The mark  should
match the mark
in fixed position.
•
Insert the power plug into the mains socket.
•
Immerse the blender attachment (1) into the bowl
with products that you want to chop/mix; you can
use the measuring cup (6) for it.
•
To switch the blender on, press and hold the button
(4). Set the required operation speed from 1 to 15
using the control knob (5). Use this operation mode
for mixing liquid products.
MW-1160.indd 9
on the blender attachment (1)
•
If you press and hold the button (3), the unit will
operate at maximum rotation speed. Use this opera-
tion mode for combined processing of liquid and
hard products.
Notes:
–
Products should be put into the bowl before the
unit is switched on. The amount of processed food
should not exceed 2/3 of the capacity of the bowl in
which the food is processed.
- Before you start chopping/mixing, we recommend to
peel fruit, remove inedible parts, such as stones, and to
cut fruit into approximately 2х2 cm cubes.
•
After you finish using the unit, unplug it and
remove the blender attachment (1) by turning
it counterclockwise so that the mark  on the
motor unit (2) is opposite the mark
Attention!
•
Do not remove the blender attachment (1) dur-
ing operation.
•
To avoid damaging the blades, do not process
too hard products such as cereals, rice, spices,
coffee beans, cheese and frozen food.
•
While using the blender attachment, if the
products are difficult to process, add some
water into the bowl, if possible.
Using the whisk
Use the whisk (11) only to make cream, biscuit dough or
mixing ready desserts.
WARNING: Before assembling make sure that the
power plug is not inserted into the power socket.
•
Insert the whisk (11) into the gear (10).
•
Attach the gear (10) to the motor unit (2), matching
the mark  on the motor unit (2) with the mark
on the gear (10) and turn it clockwise till bumping.
The mark  should match the mark
(10) in fixed position.
•
Insert the power plug into the mains socket.
•
Put the whisk (11) into the bowl with products.
•
Set the required operation speed from 1 to 15 using
the control knob (5).
•
To switch the blender on, press and hold the but-
ton (4). Use this operation mode for mixing liquid
products.
•
If you press and hold the button (3), the unit will
operate at maximum rotation speed.
•
After you finish using the unit, take the power plug
out of the socket, take the whisk (11) out of the gear
(10) and disconnect the gear (10) from the motor
unit (2) turning it clockwise so that the mark 
the motor unit (2) is opposite the mark
Attention!
•
Do not use the whisk (11) to make tight dough.
•
Products should be put into the bowl before the
unit is switched on.
9
ENGLISH
.
on the gear
on
.
07.11.2013 15:58:17