Advertisement
Quick Links
Quick Guide
FastFinish Pro Texture Sprayer
For Water-Based Materials Only.
Read Operation manual 3A5725 for complete instructions and warnings.
Manuals are available by calling Graco at 1-800-690-2894, or at www.graco.com.
For Technical Assistance call 1.800.543.0339
This Quick Guide is not a substitute for reading and understanding all operation manuals
and warning labels supplied with the equipment. It is important that you read and
understand all warnings and instructions before operating this equipment.
Follow the pressure relief procedure and wear protective equipment including but not
limited to protective eye wear.
FAILURE TO FOLLOW ALL WARNINGS CAN RESULT IN SERIOUS INJURY.
SETUP
NOTICE:
Do not store spray system under pressure. This may cause damage to the spray system. Do not
allow material to dry inside hopper, hose, gun nozzles or spray system. This may cause system to fail.
Step 1: Check material nozzle before spraying to ensure there is not an air blockage. Step 2: Make sure
hopper air passageway and air supply tube are free of debris. Clean before using. Step 3: Connect one end
of air hose to the compressor air outlet fitting and the other end to the gun air inlet fitting. Step 4: Test gun
trigger. Lubricate needle seals if necessary. Step 5: Install material nozzle on front of gun and secure using
retaining ring. Pulling the trigger when installing nozzle makes assembly easier. Step 6: If using WideTex
adapter, install disc (2) on front of adapter (3) with retaining ring (1). Install a standard nozzle (4) on front of
gun with the assembly. Pulling trigger when installing nozzle makes assembly easier. If desired finish is not
achieved, try a different size standard nozzle. Step 7: Plug power cord into a properly grounded outlet.
3A7016A - EN
Advertisement
Related Manuals for Graco FastFinish Pro
Summary of Contents for Graco FastFinish Pro
- Page 1 3A7016A - EN Read Operation manual 3A5725 for complete instructions and warnings. Manuals are available by calling Graco at 1-800-690-2894, or at www.graco.com. For Technical Assistance call 1.800.543.0339 This Quick Guide is not a substitute for reading and understanding all operation manuals and warning labels supplied with the equipment.
-
Page 2: Pressure Relief Procedure
Only pressurize hopper by connecting air sup- ply tube to barbs on hopper and gun. Only use genuine Graco air supply tube 17V945. Step 6: Apply grease to hopper o-ring to make hopper lid easier to attach to the hopper. Step 7: Pressurized hopper gun only: If lid is too loose and leaks air when pressurized, adjust the four lid clamps to tighten lid. - Page 3 Step 1: Check material nozzle before spraying to ensure there is not an air blockage. Step 2: Check to make sure air relief valve moves freely when button is pushed. Step 3: Make sure hopper air passageway and air supply tube are free of debris. Only use genuine Graco air supply tube 17V945. RUPTURE HAZARD Over-pressurization can result in hopper rupture and injury.
- Page 4 NOZZLE SELECTION CHART Nozzle WideTex Disc WideTex Nozzle Size Air Volume Application Application Nozzle (mm) Air Volume Disc (standard) Simulated 6 mm (fine to Acoustic Simulated medium) Medium to High Fine High Acoustic 8 mm (coarse) Medium High Coarse High 4 mm Orange Peel Medium to High...
-
Page 5: Mixing Material
OPERATION - ADJUSTING THE SYSTEM (PRESSURIZED HOPPER GUN ONLY) Sufficient fluid output (volume and pressure) and good atomization is a balance of atomizing air, material thickness/material flow and nozzle selection. Achieving the correct balance for your application requires experimentation to achieve desired results. Keep in mind these important points when adjusting gun: •... - Page 6 CLEANUP Step 1: Perform Pressure Relief Procedure. Step 2: Drain remaining material into a bucket until most of the texture material is out of hopper. Step 3: Fill hopper with clean water. Step 4: Remove nozzle from gun. Trigger gun into bucket until most of texture mix is out of the hopper. Allow water to flow through gun until gun is clean.