Table of Contents
Advertisement
Quick Links
Operation, Repair, Parts
Fine Finish HVLP 7.0/9.0/9.5
- For portable spray applications of fine finish coatings. For professional use only.-
240 Vac Models: 257829, 257830, 257831
120 Vac Models: 257833, 257834, 257835
Maximum Working Pressure: 10 psi (0,07 MPa, 0.7 bar)
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
Registered Design No. 001147805-0001
US Patent No.: 7,950,598, 7,971,806
313753G
EN
ti13853a
Advertisement
Table of Contents
Related Manuals for Graco Fine Finish HVLP 7.0
Summary of Contents for Graco Fine Finish HVLP 7.0
- Page 1 Operation, Repair, Parts 313753G Fine Finish HVLP 7.0/9.0/9.5 - For portable spray applications of fine finish coatings. For professional use only.- 240 Vac Models: 257829, 257830, 257831 120 Vac Models: 257833, 257834, 257835 Maximum Working Pressure: 10 psi (0,07 MPa, 0.7 bar)
-
Page 2: Table Of Contents
Operation Tips ......7 Graco Standard Warranty ....18 Maintenance . -
Page 3: Warnings
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applica- ble. - Page 4 Do not kink or over-bend the hose. • Do not expose the hose to temperatures or to pressures in excess of those specified by Graco. • Do not use the hose as a strength member to pull or lift the equipment.
-
Page 5: Grounding And Electric Requirements
Warnings Grounding and Electric Requirements This equipment requires a 240 Vac, 50 Hz, 15A circuit, Use 3-wire, 12 awg, 50 ft (15 m) or shorter, extension with a grounding receptacle. cords with ground prong. Do not alter the ground prong or use an adapter. Sprayer Components Table Sprayer Model... -
Page 6: Component Identification
Provides filtered air for spray ter and main) gun and motor R Storage tray Provides extra storage ™ Cleaning cup Provides storage for cleaning Graco EDGE spray gun G Spray gun holder ™ with EasyGlide trigger EDGE spray gun Provides external storage for... -
Page 7: Setup
Setup Setup Fluid Preparation Pressure Relief Procedure • Strain fluids before you spray. This includes color, reducers and hardeners. • Use a slower drying reducer or thinner to compen- sate for the faster drying time caused by the warm air The spray gun siphon cup is pressurized by the gun of the turbine. -
Page 8: Maintenance
Maintenance Maintenance The sprayer system is lifetime lubricated. The only main- • Tap filter gently on flat surface, dirty side down. tenance required is filter cleaning and replacement. • Direct, compressed air (100 psi(7 bar, 70 MPa) maximum) through filter panel in the opposite direction of arrows on side of filter (from the clean Filter Operation side to the dirty side. -
Page 9: Troubleshooting
Extension cord must be 3-wire, 12 AWG, 50 ft (15 m) or shorter. Hose too long Replace with shorter hose. See Graco Fine Finish Solutions brochure for hose part numbers. Circuit breaker trips Filter clogged Clean filter and replace as necessary High ambient temperature Move sprayer to cooler area. -
Page 10: Repair
Repair Repair Sprayer Disassembly 3. Place sprayer upside down. Remove four screws (77) from sprayer base plate (2). To avoid injury, including electric shock turn off sprayer and unplug power cord before performing any repair procedures on the turbine. 1. Remove four thumbscrews (18) and remove filter retainer (17), prefilter (20) and main filter (16). -
Page 11: Turbine Replacement
Turbine Replacement Turbine Replacement Refer to Parts Drawing, page 14. 7. Install new gaskets (21, 23, 24, 59 and 60). Use min- eral spirits solvent (also called white spirit) to remove 1. Follow Sprayer Disassembly procedure, page 10. any adhesive remaining from old gaskets. 2. -
Page 12: Wiring Diagrams
Wiring Diagrams Wiring Diagrams 110V Ref. Part Description Qty. 244273 Conductor, BK 15W486 Conductor, BK 15W485 Conductor, G/Y GROUND 15W484 Conductor, W 257333 Conductor, W, BK, G 240256 Conductor, W 114064 Plug, inlet 114403 Circuit Breaker, 15A 15V923 Plug, outlet, CompPack 114280 Light, indicator, 120V 120660... -
Page 13: Technical Data
Technical Data Technical Data 120 Vac, 60 Hz Maximum Hose Length Sprayer Weight Total Weight Sound Sound Ampere Watts ft (m) lb (kg) lb (kg) Power* Pressure* 11.0 40 (12,2) 28 (12,7) 38 (17,2) 94.9 dBa 82 dBa HVLP 7.0 11.0 60 (18,3) 29 (13,2) -
Page 14: Parts
Parts Parts Models 257833, 257834, 257835, 257829, 257830, 257831 ti13855a 313753G... -
Page 15: Parts List
Parts List Parts List Models 257833, 257834, 257835, 257829, 257830, 257831 Ref. Part Description Qty. Ref. Part Description Qty. 15V923 PLUG, inlet 277934 BOX, HVLP 62 ▲ 15W100 LABEL, safety 24B055 COVER, HVLP, includes 6 63 ▲ 15W223 LABEL, safety 15V791 HANDLE 15W359 SCREW, mach, hex, washer hd 15V771 LID, accessory... -
Page 16: Parts Drawing
Parts Drawing Parts Drawing Models 257833, 257834, 257835, 257829, 257830, 257831 ti12836d 313753G... -
Page 17: Parts List
Parts List Parts List Models 257833, 257834, 257835, 257829, 257830, 257831 Ref. Part Description Qty. Ref. Part Description Qty. 111593 SCREW, grounding 257066 PLATE, base, turbine, painted 102063 WASHER, lock, ext 114279 SENSOR, pressure SCREW, mach, torx pan hd 156698 O-RING 15W998 120V TURBINE 15W998 240V... -
Page 18: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.