TABLE OF CONTENTS INTRODUCTION……………………………...…..…..PAGE 3 GAME FEATURES • GAME PLAY • ASSEMBLY……………….……….…………..…..…..PAGE 4 & 5 BEFORE YOU BEGIN • TOOLS NEEDED • INSTALLATION • SETTING A.C. LINE VOLTAGE ADJUSTMENTS • SET-UP / TESTING.……………………………….…..PAGE 6 - 9 SAFETY PRECAUTIONS • PROGRAMMING YOUR GAME •...
INTRODUCTION All electronics are fully operator adjustable and are GAME FEATURES adjusted via convenient programming buttons lo- Thank you for your purchase of the new WACKY cated just inside the coin door. The game allows the DUCKS™ redemption game from I.C.E. operator to choose a timed game or a random hit game depending on the operators' location.
4. Find the location that the game will be placed in and move into rough position. 5. Remove the "Wacky Ducks™ sign on the front of the game by rotating the two locks, and 8. Inside the game, connect the rope light and lifting up on them.
Page 5
ASSEMBLY • Snap the fuse holder assembly back into the SETTING A.C. LINE power module. VOLTAGES • Plug the power cord back into the receptacle The game comes with 4 available line voltage set- in the power module, and into the wall outlet. tings as described below.
SET-UP / TESTING SAFETY PRECAUTIONS PROGRAMMING BUTTON WARNING: WHEN INSTALLING THIS GAME, A 3 Press this button to enter or exit the PROGRAM- PRONG GROUNDED A.C. RECEPTACLE MUST MING mode. You will notice when you are in the BE USED. FAILURE TO DO SO COULD RESULT Programming mode, as the displays in the Frogs will IN INJURY TO YOURSELF OR OTHERS.
Page 7
SET-UP / TESTING MODE 1 MODE 5 (GAME LENGTH) (VALUE OF XX) This mode determines how long the game lasts in This option determines the number of tickets to dis- SECONDS. The range for this value is 5-60. pense each time a dispense order is given by OP- The default value for this game is "10"...
Page 8
SET-UP / TESTING MODE 9 (FACTORY RESET) This mode has the capability to reset all options to the factory default values. The range for this option is 0-1. Setting a "1" will reset all values. The default value for this option is "0" (no reset) NOTE: THE GAME CAN ALSO BE RESET TO FACTORY DEFAULT VALUES BY TURNING THE GAME OFF, REMOVING THE BATTERY FROM...
Page 9
SET-UP / TESTING If you have the type shown in the photo below, there ROPE LIGHTING are no adjustments. The fuse located at the bottom of the printed board is the only user serviceable The rope light in the marquee is operated by a rope item.
SET-UP / TESTING NEW JERSEY SAFETY PRECAUTIONS PROGRAMMING BUTTON WARNING: WHEN INSTALLING THIS GAME, A 3 Press this button to enter or exit the PROGRAM- PRONG GROUNDED A.C. RECEPTACLE MUST MING mode. You will notice when you are in the BE USED.
Page 11
SET-UP / TESTING NEW JERSEY MODE 1 MODE 5 (GAME LENGTH) (VALUE OF XX) This mode determines how long the game lasts in This option determines the number of tickets to dis- SECONDS. The range for this value is 5-60. pense each time a dispense order is given by OP- The default value for this game is "10"...
Page 12
SET-UP / TESTING NEW JERSEY MODE 9 (FACTORY RESET) This mode has the capability to reset all options to the factory default values. The range for this option is 0-1. Setting a "1" will reset all values. The default value for this option is "0" (no reset) NOTE: THE GAME CAN ALSO BE RESET TO FACTORY DEFAULT VALUES BY TURNING THE GAME OFF, REMOVING THE BATTERY FROM...
Page 13
SET-UP / TESTING NEW JERSEY If you have the type shown in the photo below, there ROPE LIGHTING are no adjustments. The fuse located at the bottom of the printed board is the only user serviceable The rope light in the marquee is operated by a rope item.
QUICK TROUBLESHOOTING GAME WILL NOT START NO A.C. POWER CHECK POWER AT A.C. RECEPTACLE POWER MODULE SET INCORRECTLY CHECK VOLTAGE SETTING FUSE BAD IN POWER MODULE CHECK OR REPLACE FUSE FUSE BAD ON MAIN P.C. BOARD CHECK OR REPLACE FUSE NO CREDITS INSERT PROPER AMOUNT OF COINS BAD COIN MICRO SWITCH...
MECHANICAL REPAIR BACKGROUND PUNCHING GLOVE ASSEMBLY OVERVIEW The WACKY DUCKS™ game has been designed to be as easy as possible to repair. The punching glove system is designed for high reli- The duck belt can be easily adjusted while in the ability and safety.
Page 16
GAME REPAIR If you see that the thermal switch is good, check to 3. Remove the 2 square drive screws that hold the see that the coil and the diode on the coil are good. cardboard fan shroud in place. Disconnect the coil and unsolder 1 side of the diode.
Page 17
GAME REPAIR 6. Remove the hex nuts that secure the 2 long shoulder bolts to the puncher mounting bracket. Unscrew the two shoulder bolts from the puncher mounting bracket. The puncher assembly should now be able to be removed. 7. Remove the 2 screws that hold the coil retaining bracket to the puncher bracket.
Page 18
GAME REPAIR 7. Loosen the 4 adjusting bolts on BOTH ends of IF THE BELT RUNS BACKWARDS THE BELT the assembly to loosen up the duck belt. COULD BE SEVERELY DAMAGED. 5. Remove the 4 bolts that hold the belt assembly into the game.
Page 19
GAME REPAIR 6. FOLLOW THE DUCK BELT ADJUSTMENT PROCEDURES AT THE END OF THIS SEC- TION. DUCK BELT ADJUSTMENT 1. PRELIMINARY ADJUSTMENT - Loosen the 4 bolts that hold the duck belt assembly to the cabinet. They should be loose enough that the entire unit can be slid back and forth easily.
Page 20
AGE OR FRAYING OF THE BELT MATERIAL OR COULD DAMAGE THE SEWN BELT SEAM. BULB REPLACEMENT ROPE LIGHT 1. Remove the WACKY DUCKS™ sign from the front of the game. Disconnect the rope light connector and the 2-wire speaker harness.
• Clean dirt and grime from the punching mecha- nisms if they become sluggish. ™ 2. Remove the WACKY DUCKS sign from the front of the game. NOTE: DO NOT USE ANY LUBRICANT ON THE PUNCHING MECHANISMS, AS THIS WILL ONLY 3.
Need help?
Do you have a question about the WACKY DUCKS and is the answer not in the manual?
Questions and answers