Sony VENICE 2 Operating Instructions Manual page 89

89
3. Camera Operations: Technical Menu
Technical > Network
Makes settings related to the network.
Menu item Setting
Subnet Mask (DHCP/On:
obtain automatically, DHCP/
Off: 255.255.255.0)
MAC Address
Regenerate Password (Run/
Cancel)
Technical > Alerts & Tally
Makes settings related to the REC button and media capacity alerts.
Menu item Setting
Rec Light On/Off
Rec Start/Stop Beep 0 to 99
Media Near Full 1min/3min/5min
Alarm
Technical > Batt./Voltage Alarm
Makes settings related to batteries and external DC power supply voltage alarms.
Menu item Setting
Near End:Info Battery 5% to 100% (5% increments)
End:Info Battery 0% to 5%
Near End:Sony 11.5V to 17V (0.1V increments)
Battery
End:Sony Battery 11.0V to 12.5V (0.1V
increments)
Near End:Other 11.5V to 17V (11.8V) (0.1V
Battery increments)
Description
Enter the subnet mask of the unit.
Enabled when DHCP is set to Off.
[Note]
Configurable only when Network Mode is set to
Station.
Displays the MAC address of the wireless LAN
adaptor connected to the unit.
Regenerates the password (execute by
selecting Run).
[Note]
Executable only when Network Mode is set to Access
Point.
Description
Turns the REC lamp on/off.
Adjusts the volume of the beep sound
emitted when recording starts and stops.
Sets the alarm threshold for notification that
the remaining media is low.
Description
Sets the threshold value at which the
remaining battery capacity indicator starts
flashing when using a Sony Info battery.
Sets the threshold value for displaying the
"Battery End" warning when using a Sony Info
battery.
Sets the threshold value at which the
remaining battery capacity indicator starts
flashing when using a Sony non-Info battery.
Sets the threshold value for displaying the
"Battery End" warning when using a Sony
non-Info battery.
Sets the threshold value at which the
remaining battery capacity indicator starts
flashing when using a non-Sony battery.
Technical > Batt./Voltage Alarm
Makes settings related to batteries and external DC power supply voltage alarms.
Menu item Setting
End:Other Battery 11.0V to 14V (0.1V increments)
Detected Battery Sony Info Battery/Sony
Battery/Other Battery/DC IN
(12V)/DC IN (24V)
DC Low Voltage1 11.5V to 17V (0.1V increments)
DC Low Voltage2 11.0V to 14V (0.1V increments)
DC(24V) Low 22.5V to 34.0V (0.1V
Voltage1 increments)
DC(24V) Low 22.0V to 28.0V (0.1V
Voltage2 increments)
Technical > Panel Control
Makes settings related to the displays.
Menu item Setting
Brightness level High/Mid/Low/Minimum
Lock Operator Side without Rec Button
without Assign3 Button /
without Rec/Assign3 /
with Rec/Assign3 Button
Lock Assistant Side without Rec Button
with Rec Button
Description
Sets the threshold value for displaying the
"Battery End" warning when using a non-Sony
battery.
Displays the result of automatic battery pack
type detection.
Sets the threshold value for displaying a low
voltage warning when using an external
power source connected to the DC IN
connector.
Sets the threshold value for displaying an
undervoltage warning when using an external
power source connected to the DC IN
connector.
Sets the threshold value for displaying a low
voltage warning when using a 24 V external
power source connected to the DC IN
connector.
Sets the threshold value for displaying an
undervoltage warning when using a 24 V
external power source connected to the DC IN
connector.
Description
Adjusts the brightness of the sub display and
mini display.
/ Sets whether to lock the REC button or
Assign3 button operation when buttons are
locked using the LOCK switch on the Operator
side.
/ Sets whether to lock the REC button operation
when buttons are locked using the LOCK
switch on the Assistant side.