Sony VENICE 2 Operating Instructions Manual page 102

102
4. Network: Network Setup and Operations
4
Set Technical > Network > Wireless >
Network Mode (page 88) in the full
menu to Station.
5
Select Technical > Network > Wireless >
WPS (page 88) in the full menu.
6
Select Run by turning the MENU dial, then
press the MENU dial.
7
Press the access point WPS button.
For details about WPS button operation,
refer to the instruction manual for the
access point.
[Note]
If the connection fails, perform the procedure again from
1
step .
Connecting by entering a SSID and password
Connect by entering the SSID and password
on the unit.
1
Set Technical > Network > Setting
(page 87) in the full menu to Wireless.
[Note]
Grayed out and cannot be changed if a password is
not configured using Technical > Authentication >
Password (page 87) in the full menu.
2
Set Technical > Network > Wireless >
Network Mode (page 88) in the full
menu to Station.
3
Set the following items in Technical >
Network > Wireless (page 88) in the full
menu.
• SSID
• Password
• DHCP
• IP Address
• Subnet Mask
4
Select Set to confirm.
[Note]
Always use Set to confirm the settings. If the settings are
not confirmed using Set, the configured settings are not
applied.
Connecting using access point auto detection
The unit can connect by detecting connection
access points automatically, without having to
enter the SSID manually.
1
Set Technical > Network > Setting
(page 87) in the full menu to Wireless.
[Note]
Grayed out and cannot be changed if a password is
not configured using Technical > Authentication >
Password (page 87) in the full menu.
2
Set Technical > Network > Wireless >
Network Mode (page 88) in the full
menu to Station.
3
Select Technical > Network > Wireless >
Scan Networks (page 88) in the full
menu.
4
Select Run by turning the MENU dial, then
press the MENU dial.
The unit starts auto detection of
connection access points. When auto
detection finishes, networks available for
connection are displayed in a list.
5
Select the network to be connected by
turning the MENU dial, then press the
MENU dial.
6
Select Set to confirm.
A password input screen appears.
7
Enter the password, then select Done.
The Wireless preferences screen appears.
8
Set the following items in Technical >
Network > Wireless in the full menu, then
select Set to confirm.
• DHCP
• IP Address
• Subnet Mask
[Note]
Always use Set to confirm the settings. If the settings are
not confirmed using Set, the configured settings are not
applied.
Displaying the Web Remote
Control
The web remote control is displayed when
the unit is accessed from the browser of a
device. The web remote control screen is
automatically resized to match the screen size
of the connected device.
1
Connect the unit and device as described
in "Connecting the Unit and Device via
Wired LAN" or "Connecting the Unit and
Device via Wireless LAN".
2
Launch a browser on the device and enter
"http://IP address of unit/rm.html" in the
URL bar.
You can check the IP address of the unit
using Info category > System > IP Address
(page 58) in the menu.
For example, if the IP address is
192.168.1.1, enter "http://192.168.1.1/
rm.html" in the URL bar.
3
Enter the user name and password
(Technical > Authentication (page 87)
in the full menu) on the browser screen.
When connection is successful, the web
remote control screen appears on the
device.
[Note]
The page may not be displayed correctly on a
smartphone or other device if the viewing mode is set
to mobile pages. Change the viewing mode to desktop
pages.
Web Remote Control Screen
Global Menu
Select (Global Menu) at the top left of
the web remote control screen to display the
Global Menu. Select the item you want to
configure.
Camera Control screen
The Camera Control screen contains the
Camera screen, Lens screen, and Info screen.
Select the Camera tab to display the Camera
screen, the Lens tab to display the Lens
screen, and the Info tab to display the Info
screen.
Various display items and operation buttons
are displayed on the Camera Control screen
(common to Camera screen, Lens screen, Info
screen, and playback screen).
• Network connection status (Connected/
Disconnected)
• Camera ID*
• Rec button
• Assignable buttons (1 to 4, A to C)
* The Camera ID text color is the same color set using
Frame Line A/B Setup > Color.