Sony VENICE 2 Operating Instructions Manual page 15

15
1. Overview: Location and Function of Parts
18.
SDI output REC trigger indicator
Displays the SDI output REC trigger status.
State
Technical > System Configuration > SDI Rec
Remote Trigger in the full menu
Off
HD SDI Remote I/F
Parallel Rec
19.
Network connection status indicator
Displays the network connection status (LAN
or Wi-Fi).
State
Disconnected or other error (valid
network connection settings)
Connected (valid network connection
settings)
Network connection function not
used
20.
High Key/Low Key indicator (Monitor
output)
Displayed when the Monitor output is High
Key (screen for checking blown-out highlights)
or Low Key (screen for checking blocked-out
shadows) (displayed for Monitor Out output).
21.
Audio level meter indicators
Displays the levels of audio channels 1 and 2
while recording.
22.
Recording media state/remaining
capacity indicator for each media slot
Displays the state and remaining capacity of
the media in AXS memory card slots A/B.
A (recording active) icon on the left of "AXS"
indicates the recording target media.
Display
Recording command
superimposed on the SDI output
– (Blank)
Stop command Top: SDI
Bottom: Stop
Rec command Top: SDI
Bottom: REC
Stop command Top: SDI-P
Bottom: Stop
Rec command Top: SDI-P
Bottom: REC
An indicator (active slot icon) on the upper
right of the slot A/B icon on the right of "AXS"
indicates the playback target media (green
indicator indicates media is being played).
Display
A (warning) icon is displayed for media if a
Flashing
condition occurs that could impact recording.
23.
Spirit level gauge graphical indicator
On
Displays the horizontal tilt of the unit in ±0.1°
increments, up to ±10°.
Blank
You can adjust the zero angle alignment of
the spirit level gauge by executing Technical
> Special Configuration > Level Gauge Adjust
(page 87) in the full menu.
24.
Clip name display
Displays the first 8 characters of the name
of the next clip to be recorded in recording
standby mode.
Displays the first 8 characters of the name
of the clip currently being recorded when
recording.
25.
Recording status indicator
Displays the following recording operation
states of the unit.
Display Description
Recording

Rec
(Rec)
Recording standby
Stby
(Stby)
Picture cache recording

Cache
(Cache)
standby
CALL command
CALL
(CALL)
incoming
When Monitoring > Overlays/Frame Line > VF,
SDI 1/2, SDI 3/4, Monitor, or HDMI > Overlay
(page 79) is set to Rec Ind. in the full menu,
the information display for the configured
output destination is set to display only the
recording operation status.
26.
Look information display
Displays the selected Look (page 67).
27.
High Key/Low Key indicator (viewfinder
output)
Displayed when the viewfinder output is High
Key (screen for checking blown-out highlights)
or Low Key (screen for checking blocked-out
shadows) (displayed for viewfinder output).
28.
Time data display
Displays the duration or timecode, depending
on the TC/Media category > TC Display setting
in the menu (page 56).
29.
Iris position indicator
Displays the iris position (only when a lens
that is compatible with the iris setting display
function is attached).
The iris position indicator displays in 1/3 stop
increments when using an E-mount lens.
[Note]
The F-stop value is displayed instead of the T-stop value
if the T-stop value cannot be obtained.
30.
Focus position indicator
Displays the focus position (only when a lens
that is compatible with the focus setting
display function is attached).
31.
Zoom position indicator
Displays the focal length of the zoom
(displayed only when a lens that supports the
zoom setting indicator is attached).
32.
Spirit level indicator
Displays horizontal level information
numerically.
R (Roll) indicates the left-to-right horizontal tilt
of the unit.
T (Tilt) indicates the front-to-rear vertical tilt of
the unit.
You can adjust the zero angle alignment of
the spirit level gauge by executing Technical
> Special Configuration > Level Gauge Adjust
(page 87) in the full menu.
33.
Recording LUT indicator
Displays the LUT setting for recording.
34.
Recording media format (codec) indicator
Displays the format of the recording on an AXS
memory card.
35.
Base ISO indicator
Displays the configured base sensitivity.
36.
Effective picture size indicator
Displays the effective picture size and whether
anamorphic de-squeeze conversion is applied,
set using Project category > Imager Mode in
the menu. In Surround View mode, a "Sur.V"
icon is displayed below the anamorphic
conversion ratio icon (page 54).
A "Z 17:9" icon is displayed when Project
category > Zoom to Fit (page 55) is set to
17:9 in the menu. A "Z 16:9" icon is displayed
when Zoom to Fit is set to 16:9.
37.
Camera ID indicator
Displays the Camera ID setting (page 76).