Ruckus Wireless ZoneFlex 7055 Quick Setup Manual page 2

S 3: L I AP
TEP OG NTO THE
1 Open a Web browser window. and enter this URL to con-
nect to the AP:
https://192.168.0.1
2 Press <Enter> to initiate the connection. When a security
OK/Yes
alert dialog box appears, click
3 When the Ruckus Wireless Admin login page appears,
enter the following:
• Username : super
• Password : sp-admin
Login
4 Click .
S 4: C W
TEP USTOMIZE THE IRELESS
Configuration
1 On the Web interface menu, click
Wireless [2.4G/5G] . The Configure :: Wireless :: Com-
mon options appear.
2 Verify that the following options are active:
Channel
• : SmartSelect
Country Code
• : If you are not located in the United
States, select your current country.
3 Click Update Settings if you made any changes.
4 Click any of the eight "Wireless #" tabs at the top of the
page.
Enabled
5 In Wireless Availability, click
SSID
6 Delete the text in the field and enter a name for the
wireless network that will help your users identify the AP
in their wireless network connection application.
Update Settings
7 Click to save your changes.
8 Repeat Steps 4-7 for each Wireless # interface that you
want to enable.
9 Click Logout to exit the Ruckus Web Admin interface.
10 Disconnect the AP from the computer and from the cur-
rent power source, and then restore your computer's
original network settings.
S 5: M AP
TEP OUNT THE TO THE
Ensure that you use a Cat5e or better Ether-
IMPORTANT:
net cable to supply PoE power and LAN connectivity run-
ning to the outlet box where the AP will be installed.
1 Prepare the electrical outlet box.
The ZoneFlex 7055 can be mounted to a variety of com-
monly used electrical outlet box formats, including US-
style outlet boxes conforming to NEMA-WD6, and EU-
style outlet boxes conforming to BS 4662.
NOTE: The ZoneFlex 7055 comes with a bracket for a sin-
gle 1-gang electrical outlet box. For adjacent outlet boxes,
use the optional Ruckus Wireless ZF7055 adjacent wall
bracket kit (part number 902-0111-000).
to proceed.
• Remove the outlet box cover from the outlet box,
retaining the original box cover screws.
• Align the mounting bracket with the outlet box so
that the screw holes line up (the bracket provides
multiple holes for different outlet box designs), and
pull the Ethernet cable through the center of the
mounting bracket.
S
ETTINGS • Affix the mounting bracket to the outlet box using
the original outlet box cover screws. If the original
>
outlet box screw heads extend over 2mm from the
bracket, then use the enclosed low profile mounting
screws instead.
• Run the required cables through the electrical outlet
box allowing sufficient slack for the cables to reach
the not yet installed ZoneFlex 7055.
2 Connect the cables.
• Connect an Ethernet cable providing PoE power and
network connectivity to the PoE In LAN / Uplink port
using either a standard RJ45 connector or the 110
punch-down block.
.
ZoneFlex Indoor Access Point User Guide for ZF 7055
110 punch-down block wiring details).
• If PoE power is not available, the AP can be powered
using an optional DC power adapter (Ruckus part
#902-0170-XX10, sold separately)
• If required, connect the cable providing support for
pass-through devices to the Pass Through port.
Pass Through
port
O B
UTLET OX
PoE In
LAN/Uplink
Published June 2013, Part Number 800-70432-001 Rev B
Do not connect both . (See
110
Punch-down
block
Rear view
Copyright © 2013 Ruckus Wireless, Inc.
NOTE: The status LEDs are intentionally not visible once
the 7055 is mounted. Complete any verification or trouble-
shooting that requires visibility of the LEDs before mount-
ing.
3 Mount the AP to the bracket.
• Snap the AP onto the mounting bracket by hooking
the two locking tabs on the bottom of the bracket
into the slots on the bottom of the AP. Then push the
top of the AP in toward the wall until it snaps in
place.
• Use the two Torx bracket screws provided to secure
the AP to the mounting bracket using a T10 Torx
screwdriver.
Torx bracket
screw
You have completed the physical installation.
F M I
OR ORE NFORMATION
Refer to the ZoneFlex Indoor Access Point User Guide for
more detailed configuration and management information.