Raven AccuBoom Installation Manual
For case ih spx3310
Hide thumbs
Also See for AccuBoom:
- Installation manual (26 pages) ,
- Calibration & operation manual (24 pages) ,
- Parallel installation manual (16 pages)
Related Manuals for Raven AccuBoom
Summary of Contents for Raven AccuBoom
- Page 1 Case IH SPX3310 CAN AccuBoom Installation Manual Manual No. 016-0171-005 Rev. C 12/16 E28917 Copyright 2016...
- Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 Introduction......................1 Instructions for Hose Routing ....................2 Chapter 2 Cable Installation....................5 Components Needed ........................ 5 AccuBoom Installation ....................... 5 Chapter 3 System Troubleshooting ..................9 Manual No. 016-0171-005 Rev. C... - Page 4 Table of Contents Case IH SPX3310 CAN AccuBoom Installation Manual...
-
Page 5: Chapter 1 Introduction
C H A P T E R 1 The AccuBoom system is designed to provided worry free turn-on and turn-off of your booms with respect to the as-applied coverage map. The following instructions are designed to assist you in the proper installation of the AccuBoom system. -
Page 6: Instructions For Hose Routing
Avoid contact with any sharp edge or abrading surfaces such as, but not limited to: • Sheared or flame cut edges • Edges of machined surfaces • Fastener threads or cap screw heads • Ends of adjustable hose clamps Case IH SPX3310 CAN AccuBoom Installation Manual... - Page 7 INTRODUCTION Routing should not allow hoses to: • Hang below the unit • Have the potential to become damaged due to exposure to the exterior environment. (i.e. tree limbs, debris, attachments) • Be placed in areas of or in contact with machine components which develop temperatures higher than the temperature rating of hose components •...
- Page 8 HAPTER Case IH SPX3310 CAN AccuBoom Installation Manual...
-
Page 9: Chapter 2 Cable Installation
077-0180-010 ACCUBOOM INSTALLATION 1. Locate the CAN AccuBoom on the rear of the center boom section at the back of the machine. 2. Mount the Raven CAN AccuBoom node (P/N 063-0172-316) withing 5 feet of the SPX3310 boom cable connectors. - Page 10 6. Unplug the right hand boom cables from booms four to six. 7. Tee in the AccuBoom cable (P/N 115-0171-553) connectors labeled booms 4-6 LH Foam. 8. Connect the 24 ft CAN tee cable (P/N 115-0171-363) to the CAN connector located on AccuBoom cable (P/N 115-0171-553).
- Page 11 CABLE INSTALLATION 13. Locate the four pin CANbus connector below the fuse panel. 14. Connect the AccuBoom CAN connector that was routed to the fuse panel area to the CANbus connector. 15. Connect the power wire to a switched power source.
- Page 12 HAPTER Case IH SPX3310 CAN AccuBoom Installation Manual...
-
Page 13: Chapter 3 System Troubleshooting
CHAPTER C H A P T E R 3 The CAN AccuBoom Node (P/N 063-0172-316) has additional features to allow the user to diagnose the AccuBoom system. The CAN AccuBoom node has diagnostics lights that are useful for troubleshooting. FIGURE 1. Diagnostic LED Location... - Page 14 HAPTER Case IH SPX3310 CAN AccuBoom Installation Manual...
- Page 15 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
- Page 16 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.