Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Raven Manuals
  4. Farm Equipment
  5. AccuBoom
  6. Installation manual

Raven AccuBoom Installation Manual

Case ih spx 4410 can
Hide thumbs Also See for AccuBoom:

Advertisement

Quick Links

Download this manual
CASE IH SPX 4410 CAN
AccuBoom Installation Manual
P/N 0160-0171-007 Rev C
01/17
E28992
Copyright 2017

Advertisement

loading
Need help?

Need help?

Do you have a question about the AccuBoom and is the answer not in the manual?

Questions and answers

Related Manuals for Raven AccuBoom

Summary of Contents for Raven AccuBoom

  • Page 1 CASE IH SPX 4410 CAN AccuBoom Installation Manual P/N 0160-0171-007 Rev C 01/17 E28992 Copyright 2017...
  • Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.

  • Page 3: Components Needed

    AccuBoom system. See the Viper Installation and Operators Manual for instructions on setting up the software and using the AccuBoom system. You will also need a valid AccuBoom Control Activation Key for your Viper system in order to activate the AccuBoom system.
  • Page 4 Case IH SPX4410 AccuBoom Installation and Operators Manual Notes:...
  • Page 5 H A P T E R A B L E N S T A L L A T I O N Use the following procedure to properly install AccuBoom on a Case SPX4410 sprayer: 1. Mount the CAN AccuBoom on the rear of the machine: a.
  • Page 6 Accuboom cable connected to accuboom node. Mount CAN Accuboom Node Here 3. Connect the AccuBoom cable to the sprayer boom harness. a. Unplug the left-hand boom cable for booms 1 to 3. b. Tee in the AccuBoom cable (P/N 115-0171-553) connectors labeled Booms 1-3 LH Foam.
  • Page 7 AccuBoom Cable AccuBoom connections to boom harnesses 4. Route the CAN and the power cables from the AccuBoom node to the cab: a. Connect the 24 ft. CAN tee cable (P/N 115-0171-363) to the CAN connector located on the Accuboom cable (P/N 115-0171-553).
  • Page 8 Case IH SPX4410 AccuBoom Installation and Operators Manual c. Route the CAN tee cable (P/N 115-0171-363) and the power and ground wires from the AccuBoom cable (P/N 115-0171-553) to the front of the machine. Can cable routed into cab from bottom side of cab 5.
  • Page 9 Insert the round CANBus cable into the CAN splice connector. Connect the CANBus connector to the CAN splice connector 7. Connect the AccuBoom CAN cable to control the CANBus: a. Locate the 4-pin CANbus connector below the fuse panel.
  • Page 10 Case IH SPX4410 AccuBoom Installation and Operators Manual b. Connect the AccuBoom CAN connector previously routed to the fuse panel area to the CANbus connector. SPX 4410 CAN 4-pin Gateway Interface connector Note: There may be a terminator located in the wiring harness directly behind the cab.
  • Page 11 RO U B L E S H O O T I N G The CAN AccuBoom node (P/N 063-0172-316) has additional features to allow the user to diagnose the AccuBoom system. The CAN AccuBoom node has a plastic window in the case that allows the user to view green diagnostic lights.

  • Page 12: Limited Warranty

    Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...

  • Page 13: Extended Warranty

    How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.