Table of Contents
Advertisement
en Basic operation
Setting
1
00 (softened)
01 (soft)
02 (med.)
03 (hard)
2
04 (very hard)
Only set this if you will be using solely softened water.
1
Also set for mineral water. Only use non-carbonated mineral water.
2
7.2 Initial configuration
When the appliance is connected to the electricity sup-
ply for the first time or following a lengthy power cut,
you need to configure the settings before you can use
it. It may take a few seconds for the settings to appear
in the display.
Turn the control ring to change the setting as re-
1.
quired.
Possible settings:
– Language
– Clock
– Water hardness
Press
to confirm.
2.
a The next setting appears.
Work through the settings and make changes as re-
3.
quired.
a After the last setting, a note appears in the display
confirming that the initial configuration is complete.
a The time that is set appears on the display.
To check the appliance before heating for the first
4.
time, open and close the appliance door once.
7.3 Cleaning the appliance before using it
for the first time
Clean the cooking compartment and accessories be-
fore using the appliance to prepare food for the first
time.
Remove the product information and the accessor-
1.
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
the adhesive tape that is in or on the appliance.
8 Basic operation
8.1 Switching on the appliance
Press
to switch the appliance on.
▶
a The Bosch logo appears in the display. The types of
heating then appear.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance will switch itself off automatically if it is
not used for a certain period of time.
Press
to switch the appliance off.
▶
a The appliance switches off. Any functions currently
in progress are cancelled.
a The time or residual heat indicator appears in the
display.
12
Water hardness in
mmol/l
-
Up to 1.5
1.5–2.5
2.5–3.8
Above 3.8
2.
3.
4.
5.
6.
a Once the time has elapsed, an audible signal
7.
8.
9.
10.
8.3 Starting operation
You must start each operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
▶
▶
▶
a The settings, the running time, the display ring and
German hardness in
°dH
-
Up to 8.4
8.4–14
14–21.3
Above 21.3
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
Press
to switch the appliance on.
Fill the water tank.
→ "Filling the water tank", Page 15
Apply the following settings:
Type of heating
Temperature
Added steam
Cooking time
→ "Basic operation", Page 12
Press to start.
Keep the kitchen ventilated while the appliance is
‒
heating.
sounds and the display shows the time as zero.
Press
to switch the appliance off.
Once the appliance has cooled down, clean the
smooth surfaces in the cooking compartment with
soapy water and a dish cloth.
Clean the accessories thoroughly using soapy water
and a dish cloth or soft brush.
Empty the water tank and dry the cooking compart-
ment.
→ "After every steam operation", Page 17
Do not use the appliance if there is water on the
cooking compartment floor.
Wipe away any water on the cooking compartment
floor before operation.
Press to start.
the heating line appear in the display.
French hardness °fH
-
Up to 15
15–25
25–38
Above 38
4D hot air
Maximum
03
1 hour
Advertisement
Table of Contents
