This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury. Note This signal word indicates important information (e.g. material damage), but does not indicate hazards. cordless pendulum action jigsaw PJSS 11-20V...
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. cordless pendulum action jigsaw PJSS 11-20V...
Page 4
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. cordless pendulum action jigsaw PJSS 11-20V...
Page 5
• Clean the shank of the saw blade before inserting it. A dirty shank cannot be fastened securely. We recommend using the power tool with original Trotec • Check the saw blade for tight fit. A loose saw blade accessories.
Page 6
Electric shock due to lightning strike. Do not work outdoors in case of approaching thunderstorms. In case of a thunderstorm, disconnect the device from the mains. The operator is responsible for the lightning protection of the building. cordless pendulum action jigsaw PJSS 11-20V...
Page 7
The device is not a toy and does not belong in the hands of children. Warning Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy. cordless pendulum action jigsaw PJSS 11-20V...
Furthermore the device is equipped with a fan function for a cutting line without sawdust and with an integrated connection for effective external vacuum cleaning. Device depiction cordless pendulum action jigsaw PJSS 11-20V...
Page 9
• 1 x Sliding block Excessive noise can lead to hearing loss. • 1 x Rechargeable battery • 1 x Quick charger • 1 x Allen wrench • 1 x Transport case • 1 x Manual cordless pendulum action jigsaw PJSS 11-20V...
• Remove the battery from the device. • Remove the tool from the tool holder. • If attached, disconnect the dust extraction system from the device. • Clean the device as described in the Maintenance chapter. cordless pendulum action jigsaw PJSS 11-20V...
Remove the charger's mains plug before inserting or removing the battery. Never charge the battery at ambient temperatures below 10 °C or above 40 °C. The battery is partially charged upon delivery to avoid damage to the battery caused by a deep discharge. cordless pendulum action jigsaw PJSS 11-20V...
Page 12
Please proceed as follows to remove or insert a saw blade: 1. Remove the battery (13) from the device (see Removing the battery). 2. Detach the protective cover (24). 2. If required, charge the battery (13) as described in the section Charging the battery. cordless pendulum action jigsaw PJSS 11-20V...
Page 13
6. Then let the fastening clips (26) lock in place at the rear. 7. Check the sliding block (27) for tight fit. 8. Refit the battery (13; see Inserting the battery). cordless pendulum action jigsaw PJSS 11-20V...
Page 14
When doing so, make sure that the smooth side of the anti-splinter guard (18) points away from the device. 5. Refit the battery (13; see Inserting the battery). cordless pendulum action jigsaw PJSS 11-20V...
Page 15
The rip fence can be fastened on both sides of the device. 1. Remove the battery (13) from the device (see Removing the battery). 2. Loosen the locking screws (23) at the slot. Make sure not to unscrew the locking screws completely. cordless pendulum action jigsaw PJSS 11-20V...
1. Set the pendulum action selector switch (5) to the desired level. The higher the level, the larger the pendulum stroke. • The saw blade should not be longer than required for the The pendulum action can also be adjusted during intended cut. operation. cordless pendulum action jigsaw PJSS 11-20V...
Page 17
6. Let go of the on-/off-switch (2) to stop the device. 2. For an optimum dust extraction, insert the anti-splinter ð The LED work light (7) goes out. guard (18) if possible. 3. Connect a suitable vacuum cleaner (e.g. industrial vacuum cleaner) to the dust extraction (3). cordless pendulum action jigsaw PJSS 11-20V...
Shutdown • Check the quick charger for damages. Should the quick Warning of electrical voltage charger be damaged, stop using it. Contact the Trotec Do not touch the mains plug with wet or damp hands. customer service. • Hold onto the mains plug while pulling the power cable of •...
• Keep the ventilation openings free from dust deposits to prevent overheating of the motor. • Remove dust and chips from the chip ejector. If the chip ejector is blocked, clean it with suitable means (e.g. compressed air). cordless pendulum action jigsaw PJSS 11-20V...
The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment We – Trotec GmbH – declare in sole responsibility that the must not be disposed of with the household waste at the end of product designated below was developed, constructed and its life.