Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Peak Scientific N 10DR Series
Summary of Contents for Peak Scientific N 10DR Series
- Page 1 Nitrogen N*10DR Nitrogen Generator User Manual UM – N*10DR – Rev 4...
-
Page 2: Table Of Contents
Nitrogen N*10DR Nitrogen Generator UM – N*10DR – Rev 4 Contents Contents Page Contents Document Change History Warranty Statement Safety Notice to Users RoHS Compliance Statement WEEE Compliance Statement Technical Specification Introduction Unpacking and Installation Removal of Transit Bracket Useful Information Electrical Connection Generator Environment General Dimensions... -
Page 3: Document Change History
Nitrogen N*10DR Nitrogen Generator UM – N*10DR – Rev 4 History Document Change History Rev No. Change Initials Date First Release G.L. 16.10.06 Notes added for - Indoor use only & Altitude T.G. 10.09.07 Update USA address 25/08/2008 Updated solenoid valve part # 26/01/2009... -
Page 4: Warranty Statement
These instructions must be read thoroughly and understood before installation and operation of your Peak N*10DR generator. Use of the generator in a manner not specified by Peak Scientific MAY impair the SAFETY provided by the equipment. When handling, operating or carrying out any maintenance, personnel must employ safe engineering practices and observe all relevant local health and safety requirements and regulations. -
Page 5: Rohs Compliance Statement
Nitrogen N*10DR Nitrogen Generator UM – N*10DR – Rev 4 Declaration of Conformity... -
Page 6: Technical Specification
Nitrogen N*10DR Nitrogen Generator UM – N*10DR – Rev 4 Technical Specification Generator Environment Minimum operating ambient temperature 5° C (41° F) Maximum operating ambient temperature 25° C (77° F) Maximum relative humidity Maximum Altitude 2000 Meters Nitrogen Outlet Maximum flow 30 l/min (1.1 CFM) Maximum Pressure 6.89 bar (100 psi) -
Page 7: Introduction
Thank you for selecting Peak Scientific to meet your gas generation needs, and should you require any further assistance or support please do not hesitate to contact... -
Page 8: Unpacking And Installation
Installation Unpacking and Installation Although Peak Scientific takes every precaution with safe transit and packaging, it is advisable to fully inspect the unit for any sign of transit damage. Check ‘SHOCKWATCH’ label for signs of rough handling prior to unpacking -... -
Page 9: Removal Of Transit Bracket
Nitrogen N*10DR Nitrogen Generator UM – N*10DR – Rev 4 Installation Removal of Transit Bracket Remove Rear Panel as follows:- At the rear of the unit, turn the key in the lock anti-clockwise to unlock the rear panel. Hold the rear panel by the two handles and slowly swivel the bottom of it out and lower it until the top comes free from the chassis. -
Page 10: Useful Information
Nitrogen N*10DR Nitrogen Generator UM – N*10DR – Rev 4 Installation Useful Information The diameter of the tubing which will be connected to the gas outlets is important and is determined by the length of tubing required. Failure to follow these recommendations could lead to accelerated compressor wear. -
Page 11: Generator Environment
Nitrogen N*10DR Nitrogen Generator UM – N*10DR – Rev 4 Generator Environment The Generator is designed for indoor use only. The unit should be installed adjacent to the Mass Spectrometer it is supplying. If this is not convenient then the unit can be sited elsewhere, however, consideration should be made of the lengths of pipe runs as pressure drops can result from extended runs of pipe. -
Page 12: Generator Connections
Nitrogen N*10DR Nitrogen Generator UM – N*10DR – Rev 4 Connections to Rear of Unit Connections Serial Plate Power Cord (230V ONLY) 04-1038 (EU) 04-1029 (US) Water outlet 04-1030 (UK) 1/4” BSPP female Rear panel lock 9-way D-type connector for Nitrogen outlet PC Comms. -
Page 13: Operation
The display will read - Peak Scientific Mode: APCI *Note: The outlet should be vented to atmosphere for at least 30 seconds to purge the system of impurities. -
Page 14: Control Panel / Fault Diagnosis
21 days time: 30 days System Hours To exit. MENU ENTER To display the software revision. System Hours MENU Software Rev. V1.55 To exit. MENU ENTER Mode: To display the current operating mode. Mode Peak Scientific ENTER MENU Mode: ESI Diagnostic... -
Page 15: Additional Points To Note
•Rotate knurled locking nut at base of adjustment knob to lock. Unusual Operation If at any time the generator begins to emit excessive noise or vibration, then it should be switched off and you should contact your local representative or Peak Scientific as soon as possible. System Drain Please ensure that the drain port at the rear of the generator is led to a suitable connection or container make sure the container is not sealed tight. -
Page 16: Routine Maintenance
Nitrogen N*10DR Nitrogen Generator UM – N*10DR – Rev 4 Routine Maintenance Maintenance WARNING Servicing and/or repair of the Generator should only be undertaken by a TECHNICALLY COMPETENT PERSON, with the generator in its safely isolated condition. SAFELY ISOLATED CONDITION Definition: The unit is in a Safely Isolated Condition when it is disconnected from its application, fully de-pressurised and isolated from the Electrical Supply. -
Page 17: Maintenance Log
Nitrogen N*10DR Nitrogen Generator UM – N*10DR – Rev 4 Maintenance Log Maintenance Log for Serial Number _____________ Work Done Remarks Name Date...
Need help?
Do you have a question about the N 10DR Series and is the answer not in the manual?
Questions and answers