Advertisement
Available languages
Available languages
before use. Many accidents are caused by poorly
maintained power tools�
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control�
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking
into account the working conditions and the work
to be performed. Use of the power tool for operations
different from those intended could result in a hazard-
ous situation�
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations�
• Note that when you operate a power tool, please
hold the auxiliary handle correctly, which is helpful
when controlling the power tool� Therefore, proper
holding can reduce the risk of accidents or injuries�
Battery tool use and care
• Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack�
• Use power tools only with specifically designat-
ed battery packs. Use of any other battery packs may
create a risk of injury and fire.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns�
• Avoid unintentional switching on. Ensure the
on / off switch is in the off position before inserting
battery pack. Carrying the power tool with your finger
on the on / off switch or inserting the battery pack into
power tools that have the switch in accidents�
• Do not open the battery. Danger of circuit�
• In case of damage and improper use of the bat-
tery, vapors may be emitted. Provide for fresh air
and seek medical help in case of complaints. The
vapors can irritate the respiratory system�
• When the battery is defective, liquid can escape
and come into contact with adjacent components�
Check any parts concerned� Clean such parts or re-
place them, if required�
• Protect the battery against heat, e.g., also
against continuous sun irradiation and fire. There
is danger of explosion�
WARNING! Read all safety warnings and
all instructions.
• Protect the battery charger from rain and mois-
ture. The penetration of water in a battery charger in-
creases the risk of electric shock�
• Do not charge other batteries. The battery charger
is suitable only for charging lithium ion batteries within
the listed voltage range� Otherwise there is danger of
fire and explosion.
• Keep the battery charger clean. Contamination
may cause the danger of electric shock�
• Check the battery charger, cable and plug each
time before using. Do not use the battery charger
when defects are detected. Do not open the battery
charger yourself and have it repaired only by quali-
fied personnel using original spare parts. Damaged
battery chargers, cables and plugs increase the risk of
electric shock�
• Do not operate the battery charger on easily in-
flammable surfaces (e.g. , paper , textiles , etc.) or
in combustible environments. There is danger of fire
due to the heating of the battery charger during charging�
Service
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained�
• Follow instruction for lubricating and changing ac-
cessories�
Special safety warnings
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting ac-
cessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock�
Safety guidelines during power tool op-
eration
• Fix the workpiece. Use a fixing device or a vice to fix
the work piece for safely and steadily�
• Take necessary and proper safety measures when
harmful, flammable or explosive dust is produced in
the work� For example, dust that may cause cancer is
produced during the operation� Please use dust and
chip collecting device and wear a dust mask in the
work�
• Keep workplace tide and clean� The mixed materials
would be extremely dangerous� Light metal dust would
be combusted and explode easily�
• Do not process materials that contain asbestos� As-
bestos is cancerogenic substance�
• Put down the power tool when the saw blade is fully
stopped�
• Keep hands away from sawing area� Hand shall not
hold the lower part of work piece� Your hand would be
cut when it touches saw blade�
• First start the power tool and then put the power tool
of the workpiece to process it� If the saw blade is stuck
in the workpiece and power tool would rebound�
• Attention: the base plate shall cling to the workpiece
during the sawing. If the saw blade is deflected, it
would be broken and power tool would rebound�
• Cut off the power of power tool when work is done
and take the saw blade when the power tool is fully
stopped� The power tool wouldn't rebound in this way
and it can be put down safely�
• Use undamaged and crackles saw blade only�
Bended or dull saw blade would be broken easily and
cause rebound of power tool�
English
21
Advertisement
