Maintenance - Vitek VT-6408 Manual Instruction

– The time of mating of the main unit (1)
– Press
– Press the button (11) «MIN/MAX/+» to select
– Press or press and hold the button (11)
– Press or press and hold the button (11)
Note: - if during setting of the current time
no setting buttons are pressed within 20 sec-
onds, the unit will switch to the default set-
tings.
– Press the button (12) «SET/°С/°F» to select
– When the temperature outside changes,
– To view the minimum and maximum tem-
M VT-6408.indd 5
(4) will change in increasing order, after
the main unit (1) is mated to the exter-
nal sensor (15), the indicator (4) will light
constantly and the digital indications (3) of
temperature measured by the wired sen-
sor (17), will be displayed on the display of
the main unit (1).
with the external sensor (15) depends on
the data transferring conditions from the
sensor (15) and the conditions of recep-
tion by the main unit (1) and it does not
exceed 3 minutes.
and hold the
«SET/°С/°F», time format symbols (5)
«12Н or 24Н» will be flashing on the display.
the necessary time format «12Н or 24Н»,
confirm the selected time format by press-
ing the button (12) «SET/°С/°F», the "hours"
digital time indications will be flashing on
the display.
«MIN/MAX/+» to set the current time in
"hours", press the button (12) «SET/°С/°F»
to confirm, the "minutes" digital time indi-
cations will be flashing on the display.
«MIN/MAX/+» to set the current time
in "minutes", press the button (12)
«SET/°С/°F» to confirm.
the temperature measurement units, the
temperature units are shown on the dis-
play as the symbols (8, 10) «°С/°F».
the following symbols will appear on the
display (7): – temperature rises «
temperature remains constant «
temperature decreases «
peratures consequently press the button
(11) «MIN/MAX/+», the display will show
the symbols "MIN, MAX", the digital sym-
bols of ambient and outside temperature
(2, 3) and the temperature indications (7).
– To reset the indications of minimum or
maximum temperature press the button
(11) «MIN/MAX/+» once, the minimum
temperature and the symbols "MIN" will
appear on the display, press and hold the
button (11) «MIN/MAX/+» again, the mini-
mum temperature indications will be reset.
Perform the same actions to reset the
maximal temperature indications.
– To view the current temperature con-
button (12)
sequently press the button (11) «MIN/
MAX/+» until the symbols «MIN, MAX» dis-
appear from the display.
– To reset the temperature indications (7)
in the current temperature mode press
and hold the button (11) «MIN/MAX/+»,
all the readings taken from the external
sensor (15) will be reset, after that the unit
will search for a new external sensor (15).
– Unfold the base (14) and place the main
unit (1) in the desired place, if necessary,
you can hang the main unit (1) on the wall.

MAINTENANCE

•
Do not disassemble the unit by yourself,
there are no parts inside the weather sta-
tion body which require replacement.
•
Check the batteries, if the symbols (6 or 9)
" " appear on the display, replace the
batteries.
•
Use only new batteries, do not install new
and old batteries together.
•
Insert the batteries, strictly following the
polarity.
•
After changing the batteries set the cur-
rent time on the main unit (1) and recon-
nect it with the external sensor (15).
•
Clean the main unit (1) body and the exter-
»; – nal sensor (15) with a soft, slightly damp
»; – cloth, and then wipe them dry.
•
». Do not use abrasives or solvents.
•
Do not immers the main unit (1) and the
external sensor (15) into water or any
other liquids.
5
ENGLISH
20.02.2018 9:26:22