Related Manuals for Elba Domino E35-100 XD
Summary of Contents for Elba Domino E35-100 XD
- Page 1 DOMINO COOKING HOBS Instructions for the use - Installation advices KEEP IN A SAFE PLACE Before operating this appliance, please read these instructions carefully...
-
Page 2: Declaration Of Ce Conformity
Dear Customer, Thank you for having purchased and given your preference to our product. The safety precautions and recommendations reported below are for your own safety and that of others. They will also provide a means by which to make full use of the features offered by your appliance. -
Page 3: Important Safety Precautions And Recommendations
IMPORTANT SAFETY PRECAUTIONS AND RECOMMENDATIONS IMPORTANT: This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not suitable for any non domestic application and therefore should not be used in a commercial environment. The appliance guarantee will be void if the appliance is used within a non domestic environment i.e. - Page 4 • CAUTION: this appIiance must only be installed in a permanently ventilated room in compliance with the applicable regulations. • Do not carry out cleaning or maintenance operations on the appliance without having previously disconnected it from the electric power supply. •...
- Page 5 Care should be taken to avoid touching heating elements on – the hob. To avoid burns and scalds, young children should be kept – away. • Make sure that electrical cables connecting other appliances in the proximity of the cooktop cannot come into contact with the hob.
- Page 6 ENERGY LABELLING/ECODESIGN • Commission regulation (EU) No 66/2014 (implementing Directive 2009/125/EC of the European Parliament and of the Council). Reference to the measurement and calculation methods used to establish compliance with the above requirements: • Standard EN30-2-1 (hobs: gas fired burners). USE OF THE APPLIANCE, ENERGY SAVING TIPS GAS FIRED BURNERS •...
- Page 7 ADVICE ADVICE for the for the INSTALLER INSTALLER...
- Page 8 IMPORTANT: • The appliance is designed and approved for domestic use only and should not be installed in a commercial, semi commercial or communal environment. Your product will not be guaranteed if installed in any of the above environments and could affect any third party or public liability insurances you may have. For the United Kingdom only: The appliance may be installed in a kitchen, kitchen/ diner or a bed sitting room, but not in a room or space containing a bath or a shower without first consulting current regulations.
-
Page 9: Installation
INSTALLATION TECHNICAL INFORMATION FOR THE INSTALLER In order to install the cooker top into the kitchen fixture, a hole with the dimensions shown in fig. 1.1a has to be made, bearing in mind the following: • A 30mm ventilation gap must be provided between the bottom of the appliance and any cabinetry, draw unit or appliance. - Page 10 Fig. 1.1a Cooktop installed Fig. 1.1b Measures (mm) Description (minimum) (minimum) 30cm wide models...
-
Page 11: Fastening The Cooktop
FASTENING THE COOKTOP Each cooktop is provided with an installation kit including brackets and screws for fastening the cooktop to benches from 20 to 40mm thick. The kit includes 4 tabs “A” and 4 selfthreading screws “B”. • Cut the unit. •... - Page 12 PROVISION FOR VENTILATION (UNITED KINGDOM ONLY) • The appliance should be installed into a room or space with an air supply in accordance with the current version of BS 5440-2: 2000. • For rooms with a volume of less than 5m - permanent ventilation of 100 cm free area must be provided.
- Page 13 VENTILATION REQUIREMENTS (FOR THE OTHER COUNTRIES) The appliance must be installed in compliance with applicable local regulations concerning ventilation and the evacuation of exhaust gases. Intensive and prolonged use may require extra ventilation, e.g. opening a window, or more efficient ventilation increasing the mechanical suction power if this is fitted. CHOOSING SUITABLE SURROUNDINGS The room where the gas appliance is to be installed must have a natural flow of air so that the gas can burn (in compliance with applicable local regulations).
-
Page 14: Gas Section
GAS SECTION GAS INSTALLATION REQUIREMENTS Important ! • Before installation, make sure that the local distribution conditions (gas type and pressure) and the adjustment of this appliance are compatible. The appliance adjustment conditions are given on the plate or the label. •... - Page 15 GAS CONNECTION, OPTION 1 (UNITED KINGDOM ONLY, MODELS SUPPLIED WITH CONICAL/MALE ELBOW FITTING) Cat: 2H 3+ Installation to Natural Gas Installation to Natural Gas must conform to the Code of Practice, etc. The supply pressure for Natural Gas is 20 mbar. The installation must conform to the relevant British/European Standards.
- Page 16 The fitting (fig. 2.1a) is made up of: 1/2" BSPP (G) parallel 1/2" BSPP (G) parallel – 1 nut “A” (ISO 228-1) male (ISO 228-1) female – 1 elbow fitting “C” – gasket “F” Connection to the Gas Supply – Be careful when flexible pipes are used that they do not come into contact with moving parts.
- Page 17 GAS CONNECTION, OPTION 2 (UNITED KINGDOM ONLY, MODELS SUPPLIED WITH CONICAL/MALE PIPE FITTING & OTHER EXTRA EU COUNTRIES) Cat: 2H 3+ The gas connection fitting (fig. 2.2) is made up of: • the floating nut; • the elbow; • the gaskets; •...
- Page 18 For the United Kingdom only Before connecting the appliance to the gas supply fit the conical pipe fitting (if not supplied with the appliance it can be purchased by contacting the After-Sales Service) to the elbow interposing the gasket. The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a suitably qualified, registered installer.
- Page 19 if it has an expiry date, it should be replaced before that date. • If using a flexible hose which is not entirely made of metal, make sure that it does not come into contact with any part of the cooktop with a surface temperature of 70°C or above (or refer to applicable local regulations).
-
Page 20: Lubrication Of The Gas Taps
Some models - for the gas category check the data label attached on the appliance TABLE FOR THE CHOICE OF THE INJECTORS G30/G31 Cat: II 2H 3+ 28-30/37 mbar 20 mbar G30/G31 G20/G25 Cat: II 2E 3+ 28-30/37 mbar 20/25 mbar Nominal Reduced Ø... - Page 21 REPLACEMENT OF THE INJECTORS Semi-rapid If the injectors are not supplied they can and rapid be obtained from the “Service Centre”. burner Select the injectors to be replaced according to the “TABLE FOR THE CHOICE OF THE INJECTORS”. nozzle diameters, expressed hundredths of a millimetre, are marked on the body of each injector.
- Page 22 SETTING THE MINIMUM OF THE COOKTOP BURNERS In the minimum position the flame must have a length of about 4 mm and must remain lit even with a quick turn from the maximum position to that of minimum. The flame adjustment is done in the following way: •...
-
Page 23: Electrical Section
ELECTRICAL SECTION UNITED KINGDOM ONLY IMPORTANT: The appliance must be installed in accordance with the manufacturer’s instructions. Incorrect installation, for which the manufacturer accepts no responsibility, may cause damage to persons, animals and property. The connection of the appliance to earth is mandatory. The manufacturer declines all responsibility for any inconvenience resulting from the inobservance of this condition. - Page 24 FOR THE OTHER COUTRIES – connect the blue wire to the IMPORTANT: The appliance must be terminal marked with the letter “N” installed by a qualified technician or coloured black; according with the current local – connect the brown wire to the regulations and in compliance with terminal marked with the letter “L”...
-
Page 25: Replacing The Power Supply Cable
FOR ALL THE COUTRIES REPLACING THE POWER SUPPLY CABLE WARNING: If the power supply cable is damaged, it must be replaced only by an authorised service agent in order to avoid a hazard. Use the same type of power supply cable. This cable must be connected to the terminal block following the diagram in fig. - Page 27 ADVICE ADVICE for the for the USERS USERS...
-
Page 28: Control Panel Description
FEATURES Fig. 1.1a Fig. 1.1b Fig. 1.2a Fig. 1.2b COOKING POINTS Semirapid burner (SR) 1,75 kW Rapid burner (R) 3,00 kW Triple ring burner (TR) 3,80 kW CONTROL PANEL DESCRIPTION Rapid burner control knob (2) Semirapid burner control knob (1) Triple-ring burner control knob (3) NOTE: •... -
Page 29: Gas Burners
GAS BURNERS GAS BURNERS NOTE: The knob and symbols may vary. Gas flow to the burners is adjusted by turning the knobs (illustrated in fig. 2.1) which control the safety valves. Turning the knob, so that the indicator line points to the symbols printed on the panel, achieves the following functions: –... -
Page 30: Choice Of The Burner
LIGHTING GAS BURNERS CHOICE OF THE BURNER FITTED WITH SAFETY VALVE On the control panel, near every knob DEVICE there is a diagram that indicates which burner is controlled by that knob. ignite burner, following The suitable burner must be chosen instructions are to be followed: according to the diameter and the capacity Press in the corresponding knob and... - Page 31 AUXILIARY GRATE FOR SMALL PANS (Optional) This grate is to be placed on top of the (smaller) auxiliary burner when using small diameter pans, in order to prevent them from tipping over. Fig. 2.4 CORRECT USE OF TRIPLE-RING BURNER- OPTIONAL •...
-
Page 32: Cleaning And Maintenance
CLEANING AND MAINTENANCE GENERAL ADVICE COOKING HOBS WITH • Before you begin cleaning you must GLASS LID (optional) ensure that the hob is switched off. • It is advisable to clean when the appliance is cold and especially when cleaning the enamelled parts. -
Page 33: Control Knob
GAS TAPS CORRECT REPLACEMENT OF THE SEMIRAPID AND RAPID BURNERS Periodic lubrication of the gas taps must be carried out by specialist personnel only. It is very important to check that the burner In the event of operating faults in the gas flame spreader “F”... - Page 34 Fig. 3.1 Fig. 3.2 Fig. 3.3 Fig. 3.4 Fig. 3.5...
- Page 35 The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the present booklet. The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacturer commercial reasons at any moment and without prior notice, without jeopardising the essential functional and safety characteristics of the appliances.