Woodland Mills WOODLANDER Operator's Manual

Sawmill trailer

Hide thumbs Also See for WOODLANDER:

Operator's manual (52 pages)

Operator's manual (72 pages)

Operator's manual (68 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

WOODLANDER

SAWMILL TRAILER

™

OPERATOR'S MANUAL

The Woodlander

™

is compatible with HM126 and HM130 sawmills. Woodlander

™

is a trademark of Woodland Mills, Inc.

Table of Contents

Need help?

Do you have a question about the WOODLANDER and is the answer not in the manual?

Questions and answers

Summary of Contents for Woodland Mills WOODLANDER

Page 1 WOODLANDER SAWMILL TRAILER ™   OPERATOR’S MANUAL The Woodlander ™ is compatible with HM126 and HM130 sawmills. Woodlander ™ is a trademark of Woodland Mills, Inc.
Page 2   This page intentionally left blank.
Page 3: Table Of Contents
2017 Woodlander ™ Operator’s Manual TABLE OF CONTENTS TABLE OF CONTENTS ____________________________________________1 INTRODUCTION __________________________________________________2 INTENDED USE __________________________________________________3 TECHNICAL SPECIFICATIONS ______________________________________3 GENERAL SAFETY RULES_________________________________________3 BOLT TORQUE SPECIFICATIONS ___________________________________4 INSPECTION/MAINTENANCE _______________________________________4 SAWMILL TRAILER ASSEMBLY _____________________________________5 1. UNPACKING _______________________________________________5 2. SETUP ____________________________________________________6 REPLACEMENT PARTS ORDERING ________________________________30...
Page 4: Introduction
Operator’s Manual INTRODUCTION Congratulations on your purchase and welcome to Woodland Mills. This manual gives you the necessary information about your trailer so you will be able to use it properly. The entire manual must be read and understood before you start using the trailer. If any questions should arise that are not covered by this manual, please contact Woodland Mills Inc.
Page 5: Intended Use
2017 Woodlander ™ Operator’s Manual INTENDED USE This trailer is designed to hold an HM126 or HM130 sawmill and its track system for sawing logs while the trailer is stationary and ﬁrmly supported on the ground. It is not intended to carry any additional weight or be used as a utility trailer.
Page 6: Bolt Torque Specifications
2017 Woodlander ™ Operator’s Manual BOLT TORQUE SPECIFICATIONS ITEM DESCRIPTION 78 in-lbs / 9 Nm 133 in-lbs / 15 Nm 333 in-lbs / 38 Nm 53 ft-lbs / 72 Nm 93 ft-lbs / 126 Nm INSPECTION/MAINTENANCE • Check the tires before all trips. Make sure they are inﬂated to the pressure shown on the tire.
Page 7: Sawmill Trailer Assembly
2017 Woodlander ™ Operator’s Manual SAWMILL TRAILER ASSEMBLY 1. UNPACKING Remove all the parts from the steel crate. You will use the steel crate in step 2. 0001361-M-EN: Rev A Page 01-Dec-2021...
Page 8: Setup
2017 Woodlander ™ Operator’s Manual 2. SETUP Using the hardware listed below, build the track with the gussets as shown on the next page. Make sure the track width is 30.5” (775 mm) and measure diagonally for squareness. Tighten all the bolts to the speciﬁed torque speciﬁcation. ...
Page 9 2017 Woodlander ™ Operator’s Manual 1x - End Bunk 1x - Middle Bunk 4x - M10 x 30mm 4x - M10 x 30mm 1x - Joining Bunk 4x - M10 Lock Nut 4x - M10 Lock Nut 8x - M10 x 30mm...
Page 10 2017 Woodlander ™ Operator’s Manual Place the track assembly on top of the shipping crate making sure it is centred. Using the hardware listed below, hang the side plates using the M10x25mm and M10x30mm bolts, do not tighten these bolts.
Page 11 2017 Woodlander ™ Operator’s Manual M10 x 30mm at End Stops. M10 x 25mm at all other locations. The end stops attach on the inside of the track using the M10 x 30mm bolts.  0001361-M-EN: Rev A Page 01-Dec-2021...
Page 12 2017 Woodlander ™ Operator’s Manual Using the hardware listed below, install the cross beams as shown on the next page. Make sure the crosser with the two holes goes at the front. Do not tighten these bolts. M10 x 25mm Bolt...
Page 13 2017 Woodlander ™ Operator’s Manual Front Cross Beam Cross Beam 0001361-M-EN: Rev A Page 01-Dec-2021...
Page 14 2017 Woodlander ™ Operator’s Manual Tighten all bolts to the speciﬁed torque speciﬁcation, starting from the centre and working towards the outside. Ensure the track is straight, level and square during this procedure. Place the 4 jacks under the end cross beam and the front cross beam and extend the jacks all the way.
Page 15 2017 Woodlander ™ Operator’s Manual Using the hardware listed below, install the rest of the cross beams and the jack mounts. Tighten the bolts to the speciﬁed torque. M10 x 30mm Bolt M10 Flange Lock Cross Beam Jack Mounts 0001361-M-EN: Rev A...
Page 16 2017 Woodlander ™ Operator’s Manual   0001361-M-EN: Rev A Page 01-Dec-2021...
Page 17 2017 Woodlander ™ Operator’s Manual Next, lower the trailer onto the crate and remove the jacks. Slide the jacks onto the jack mounts and secure in place with the pin attached to the jack. Raise the jacks up to enable the crate to be removed from under the trailer assembly. Place blocks of wood underneath each jack stand if necessary to achieve the required height.
Page 18 2017 Woodlander ™ Operator’s Manual Using the hardware listed below, install the axle mount lower cross beam as show. Tighten these bolts. M10 x 25mm Flange Hex Bolt M10 Flange Lock Axle Mount Cross Beam 0001361-M-EN: Rev A Page 01-Dec-2021...
Page 19 2017 Woodlander ™ Operator’s Manual Using the hardware listed below, install the axles and fender mounts as shown on the next page. Tighten these bolts to the speciﬁed torque. M12 x 35mm Bolt M12 x 75mm Bolt M12 Washer M12 Lock Nut...
Page 20 2017 Woodlander ™ Operator’s Manual   M12 x 75mm M12 x 35mm 0001361-M-EN: Rev A Page 01-Dec-2021...
Page 21 2017 Woodlander ™ Operator’s Manual Using the hardware listed below, install the trailer tongue and coupler. Leave the U-bolts loose in this step, since the plug for the lights will be routed through the tongue in a following step. Tighten the coupler bolts.
Page 22 2017 Woodlander ™ Operator’s Manual Europe M12 x 100mm North America M12 x 70mm Side plate and track rail removed for clarity. 0001361-M-EN: Rev A Page 01-Dec-2021...
Page 23 2017 Woodlander ™ Operator’s Manual Using the hardware listed below, install the lights and signs as shown on the next page. Install the tail lights on the light bar before mounting the light bar assembly on the frame. Tighten these bolts to the speciﬁed torque.
Page 24 2017 Woodlander ™ Operator’s Manual Triangle Bracket (Europe only) Triangle Reﬂector (Europe only) M6 x 20mm M5 x 20mm Pan Head M8 x 25mm Europe only 0001361-M-EN: Rev A Page 01-Dec-2021...
Page 25 2017 Woodlander ™ Operator’s Manual After the lights have been installed, the wire can be routed through the wire clamps and tongue. Using the hardware below, route the cable along the right-hand side (when at rear of trailer and facing tail lights). The tongue U-bolts from the earlier step can be tightened after wiring has been ﬁshed through the tongue.
Page 26 2017 Woodlander ™ Operator’s Manual Place the assembled saw head on the trailer and use the hardware listed below to install the head lock down brackets as shown on the next page. Tighten these bolts to the speciﬁed torque. Head Lock Down...
Page 27 2017 Woodlander ™ Operator’s Manual Remove the spacers from in-between the side plates as shown. Using the provided M6 x 25 and M6 x 40 bolts, install the brackets in place of the spacers.  M6 x 40mm through wire brush...
Page 28 2017 Woodlander ™ Operator’s Manual Drill four (4) holes for the lock down brackets using the drill bit provided. 64.5 inches (164cm) from the rear edge of the track to the rear post of the head. Insert a locking pin into each hole as they are drilled.
Page 29 2017 Woodlander ™ Operator’s Manual Using the hardware listed below, install the tires on the axles. Using a torque wrench, torque the lug nuts to 80 ft•lb / 110 Nm following the pattern shown below. Wheels Lug Nut 0001361-M-EN: Rev A...
Page 30 2017 Woodlander ™ Operator’s Manual Using the hardware listed below, install the fenders as shown. M10 x 100mm Bolt M10 x30-OD Fender Washer M10 Lock Nut Fender 0001361-M-EN: Rev A Page 01-Dec-2021...
Page 31 2017 Woodlander ™ Operator’s Manual Using the hardware below, install the safety chain on the trailer tongue. This step is not needed for European customers. M10 x 40mm Bolt (Not in Europe) M10 Washer (Not in Europe) M10 Lock Nut...
Page 32: Replacement Parts Ordering
Next, turn to the Parts Lists section and locate the balloon number in the “Item” column: Record the part number (e.g. 0001071, HHB-MBM080FCJ, etc.) in the “Part No.” column. Contact Woodland Mills through the website (or via phone/email) and provide the list of part numbers, including quantities for each item.
Page 33: Exploded Assembly Views
2017 Woodlander ™ Operator’s Manual EXPLODED ASSEMBLY VIEWS CHASSIS AND TRACK  0001361-M-EN: Rev A Page 01-Dec-2021...
Page 34: Tongue: North America
2017 Woodlander ™ Operator’s Manual TONGUE: NORTH AMERICA TONGUE: EUROPE   0001361-M-EN: Rev A Page 01-Dec-2021...
Page 35: Axles, Wheels, And Fenders
2017 Woodlander ™ Operator’s Manual AXLES, WHEELS, AND FENDERS  0001361-M-EN: Rev A Page 01-Dec-2021...
Page 36: Lighting: North America
2017 Woodlander ™ Operator’s Manual LIGHTING: NORTH AMERICA  0001361-M-EN: Rev A Page 01-Dec-2021...
Page 37: Lighting: Europe
2017 Woodlander ™ Operator’s Manual LIGHTING: EUROPE  0001361-M-EN: Rev A Page 01-Dec-2021...
Page 38: Nameplates
2017 Woodlander ™ Operator’s Manual NAMEPLATES  0001361-M-EN: Rev A Page 01-Dec-2021...
Page 39: Jacks
2017 Woodlander ™ Operator’s Manual JACKS  0001361-M-EN: Rev A Page 01-Dec-2021...
Page 40: Head Lock-Down
2017 Woodlander ™ Operator’s Manual HEAD LOCK-DOWN  0001361-M-EN: Rev A Page 01-Dec-2021...
Page 41: Parts Lists
2017 Woodlander ™ Operator’s Manual PARTS LISTS NORTH AMERICA Item Part No. Description 0001373 GUSSET, END 0001374 GUSSET, JOINING 0001363 SIDE PLATE, LONG 0001364 SIDE PLATE, SHORT 0001369 CROSS BEAM 0001370 CROSS BEAM, FRONT 0001376 JACK MOUNT 0001385 JACK STAND...
Page 42: Europe
2017 Woodlander ™ Operator’s Manual Item Part No. Description FHH-MBJ080FCJ HEX BOLT, FLANGED, CLS 8.8, M8 X 1.25, 25 mm LG, FULL FHH-MBM085FCM HEX BOLT, FLANGED, CLS 10.9, M10 X 1.5, 30 mm LG, FULL FHH-MBM090PCM HEX BOLT, FLANGED, CLS 10.9, M10 X 1.5, 35 mm LG, 26 mm LG THD FHH-MBM095PCM HEX BOLT, FLANGED, CLS 10.9, M10 X 1.5, 40 mm LG, 26 mm LG THD...
Page 43 2017 Woodlander ™ Operator’s Manual Item Part No. Description 0001390 REAR REFLECTOR, RED, EU 0001391 SIDE REFLECTOR, AMBER, EU 0001392 FRONT REFLECTOR, WHITE, EU 0001383 WOODLAND MILLS NAMEPLATE 0001393 HEAD LOCK-DOWN BRACKET 0001394 LOCK-DOWN PIN 0004720 LINCH PIN, 4.5 mm DIA, 25 mm USEABLE LG, 32 mm LG...
Page 44: Notes
2017 Woodlander ™ Operator’s Manual NOTES 0001361-M-EN: Rev A Page 01-Dec-2021...
Page 45 2017 Woodlander ™ Operator’s Manual 0001361-M-EN: Rev A Page 01-Dec-2021...
Page 46 2017 Woodlander ™ Operator’s Manual 0001361-M-EN: Rev A Page 01-Dec-2021...
Page 47 This page intentionally left blank.

Woodland Mills WOODLANDER Operator's Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Woodland Mills WOODLANDER

Summary of Contents for Woodland Mills WOODLANDER

Table of Contents