Vitek VT-6414 Manual Instruction page 6

ENGLISH
– Use the «UP» (5) and «DOWN» (6) but-
tons to select the time format. Press
the «MODE» (4) button to confirm the
selected format. Flashing numerical indi-
cation of the current time «clock» (19) will
appear on the display.
– Use the «UP» (5) and «DOWN» (6) buttons
to set the current time «clock». Press the
«MODE» (4) button to confirm the setting.
Flashing numerical indication of the cur-
rent time format «minutes» (19) will appear
on the display.
– Use the «UP» (5) and «DOWN» (6) but-
tons to set the current time «minutes».
Press the «MODE» (4) button to confirm
the setting.
The current time, date, and day of the week
«DAY» corresponding to the set date (17) will
appear on the display (2). The day of the week
indicator will be changed with the calendar:
Sun. Mon. Tue.
SUN MON TUE
Alarm actuation time setting
Before setting the alarm actuation time make
sure that the current time is set correctly.
Alarm actuation time setting: Press the
«MODE» (4) button once. The alarm actua-
tion time indicator «АL» (21), the initial alarm
(19) «7:00», and the previous alarm will
appear on the display (2).
– Press the «MODE» (4) button one more
time, and hold it for at least 2 sec-
onds - flashing numerical alarm indi-
cation «clock» (19) will appear on the
display (2).
– Use the «UP» (5) and «DOWN» (6) but-
tons to set the alarm «clock». Press the
«MODE» (4) button to confirm the setting.
Flashing numerical indication of the alarm
«minutes» will appear on the display.
– Use the «UP» (5) and «DOWN» (6) but-
tons to set the alarm «minutes». Press
the «MODE» (4) button to confirm the
setting. Flashing numerical indication of
the snooze time «05» will appear on the
display.
Note: the numerical indications «05» are
the previously set snooze time of 5 minutes.
Wed. Thru. Fri. Sat.
WED THU FRI SAT
– Use the «UP» (5) and «DOWN» (6) to
set the snooze duration between 5 and
20 minutes. To confirm the selected set-
ting press the «MODE» (4) button.
The alarm «AL» is set.
To view the set alarm time, press the «MODE»
button (4) once, and after 8 seconds the unit
will be returned to displaying the current time.
Notes:
– if the buttons «MODE» (4), «UP» (5),
«DOWN» (6) are not pressed during
8 seconds during the installation, the unit
will revert to displaying the current time.
Switching the alarm on/off
To activate the alarm, press the «MODE» but-
ton (4). The numerical indications (19) «7:00»
of the preset alarm time and the alarm set-
ting indication (21) «AL» will appear on the
display (2). Press the «UP» button (5) and
switch the alarm on, the alarm activation indi-
cation (20) « » will appear on the display.
To switch the alarm off, press the «UP» but-
ton (5) again, and the alarm on indication (20)
« » will go out.
Note: - if the «UP» button (5) is not pressed
for 8 seconds, the unit will be returned to the
current time display mode.
When the set time is reached, you will hear a
sound signal. Flashing alarm activation indi-
cation (20) « » will appear on the display.
If you do not press any buttons, the sound will
persist for 2 minutes.
Press any button to stop the alarm sound.
Note: - the alarm sound signal will be chang-
ing from single beeps to multiple ones, and
in 30 seconds the signal will start sounding
continuously.
Snooze
– When the alarm is sounding, you can press
the «LIGHT/SNZ» (3) or (8) button tem-
porarily switch the alarm off for the set
snooze time. Flashing alarm activation
indication (20) «
display. Within a set time the alarm will
sound again.
To increase or decrease the snooze time refer
to the section «The snooze setting».
6
» will appear on the