KI CrossRoads Metal Media Shelving Single Face Assembly Instructions

Figure 2
Base Assembly
Top Assembly
Flat Washer
and Hex Nut
1
4 / " Hex Head Bolts
2
with Lock Washers
and Flat Washers
Left End Panel
Figure 4
1330 Bellevue Street • P .O. Box 8100 • Green Bay, WI 54308-8100 • Tel 1-800-424-2432 • www.ki.com
CrossRoads
Figure 1
Left End Panel
Top
Assembly
2" Hex Head Bolts
with Lock Washers
and Flat Washers
Top Assembly
Left End Panel
Figure 3
2" Hex Head Bolts
with Lock Washers
and Flat Washers
Shared End Panel
Glides
© 2009 KI All Rights Reserved • Litho in USA. • Code KI-61563AR4-MM/TMI/PDF/1209
Assembly Instructions
® Metal Media Shelving
Single Face
December 2009
Base Assembly
Left End Panel
2" Hex Head Bolts
with Lock Washers
and Flat Washers
2" Hex Head Bolts
with Lock Washers
and Flat Washers
Right End Panel
Glides
Right End Panel
Base Assembly
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must
be tightened securely and must be checked periodically
after assembly. Failure to assemble properly, or to secure
parts may result in assembly failure and injury.
Tools Required:
• #2 Phillips screwdriver
• 1 / " socket
2
• Socket wrench
Hardware Included:
• #8 x 5 / " screws
8
• #8 x 1 1 /
• 5 / " x 2" hex head bolt
16
• 5 / " x 4 1
16
• / " lock washer
5
16
• 5 / " flat washer
16
• 5 / " hex nut
16
• Metal pegs
1. Set back edge of left end panel on flat
surface (holes to inside – if it's a
curved end panel make sure the
curved edge is up).
2. Align the side holes in the base
assembly with the lower holes in the
left end panel. Insert 2" hex head bolts
with lock washers and flat washers into
the base and end panel (Figure 1).
Tighten.
3. Align the side holes in the top
assembly with the upper holes in the
left end panel (Figure 2). Make sure
the faceplate on the top assembly is to
the front and that the back panel
groove is to the back. Insert 2" hex
head bolts with lock washers and flat
washers into the top assembly and
end panel. Tighten. Note: for shelving
units 72" and higher, the top shelf
assembly should be flipped so that
the cleat side faces up.
4. For single starter unit (stand-alone) and
final end panel for connecting units:
Take the right end panel (holes to
inside) and align the side with the holes
in both the base and the top assembly
Base Assembly
(Figure 3). Insert 2" hex head bolts with
lock washers and flat washers into the
base and top assembly. Tighten.
5. For adder units (connecting) – Align
the side holes in the shared panel
(holes both sides) with the holes in
both the base assembly and the top
assembly. Insert 4
with lock washers, flat washers and
nut into the base assembly. Do not
tighten (Figure 4).
6. Align the side holes in the base
assembly with the lower holes in the
shared panel. Tighten the 4
head bolts and nuts. (Figure 4).
7. Align the side holes in the top assembly
(groove side down) with the upper holes
in the left end panel. Tighten the 4
hex head bolts and nuts. (Figure 4).
" screws
4
/ " hex head bolt
2
1 / " hex head bolts
2
1 / " hex
2
1 / "
2