KI Concerto Assembly Instructions Manual
Seating with power & data
Hide thumbs
Also See for Concerto:
- Assembly instructions manual (20 pages) ,
- Disassembly instructions (2 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for KI Concerto
Summary of Contents for KI Concerto
- Page 1 Assembly Instructions Concerto Seating with Power & Data ® December 2020...
-
Page 2: Tools Required
9. Mount uprights to the floor per 12. Route data wires and insert data 18. Bolt on tablet arm (optional). 1. Read and review Concerto Seating the tablet option and the electrical jacks into their data plates before 19. Install end panel (optional). - Page 3 Detail A Tolerances for Mounting Uprights seat. Attempting to rob from an adjacent The following tolerances apply to seat may only move the problem down standard, floor-mounted Concerto. the row. They are applied to the center-to-center dimensions of the TUBE CENTERLINE FLOOR BOLT CENTERLINE uprights, e.g.
- Page 4 Figure 1 Upright Installation - Standard Upright Installation - Concerto 1. Begin installing uprights to the floor 2. At locations specified for Concerto Seating Seating with Power & Data by placing the appropriate bottom full-height side covers, use a bracket 1.
- Page 5 2. Install either the -20 x " or were installed in the previous step. need additional inward pressure on 1. Follow the Concerto -20 x 1 " T-30 Torx screw Rotate the backrest forward to line the mounting brackets to squeeze...
- Page 6 Concerto Seating with Power & Data ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble properly, or to secure parts may result in assembly failure and personal injury.
- Page 7 12VDC power source is used pages 8 and 9. for LED aisle lights. The step to the right is intended as a guideline for installation. Note: Aisle light transformers and dimmers are available. Contact KI Customer Service at: 1-800-424-2432.
- Page 8 Concerto Seating with Power & Data ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be #8 x / ” Pan Head T-20 Torx Screw tightened securely and must be checked periodically after assembly.
- Page 9 Concerto Seating with Power & Data ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble properly, or to secure parts / ”...
- Page 10 Concerto Seating with Power & Data ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble properly, or to secure parts #8 x / ”...
- Page 11 Concerto Seating with Power & Data ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble properly, or to secure parts may result in assembly failure and personal injury.
- Page 12 Figure 9 Decorative End Panels - Standard 2. Position an end panel retaining clip Concerto Seating as shown and tighten the Decorative end panels are not #10 screws, clamping the end panel available with power & data, or large to the upright (Figure 9).
- Page 13 Concerto Seating with Power & Data ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble properly, or to secure parts may result in assembly failure and personal injury.
- Page 14 3. Refer to pages 5 and 11 of the floor and anchoring hardware. installation of the uprights to the Concerto Auditorium Seating with 6. Reposition the unit and secure to the ADA removable base using the Power & Data Assembly Instructions.
- Page 15 Retrofit of Power & Data 1. Remove the pivot screws and lift the 2. Follow the space-planning layout Note: Upright locations specified Components To Concerto Seating seat assembly off the pivot brackets and position the correct number as “FL” (full-length side cover), Note: Power &...
- Page 16 (46”, 49” or 52”) (25”) receptacle receptacles 5-wire data infeed “D” power infeed Concerto Right Power & Data Infeed “P” simplex simplex distribution harness distribution harness receptacles receptacle (46”, 49” or 52”) (25”) 5-wire data infeed “D”...
- Page 17 Concerto Seating with Power & Data ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble properly, or to secure parts may result in assembly failure and personal injury.
- Page 20 1330 Bellevue Street P .O. Box 8100 Green Bay, Wisconsin 54308-8100 1-800-424-2432 www.ki.com KI is a registered trademark of Krueger International, Inc. © 2020 Krueger International, Inc. All Rights Reserved Code KI-60323R12/KI/PDF/1220...
Need help?
Do you have a question about the Concerto and is the answer not in the manual?
Questions and answers