i3 International Ax78R Quick Start Manual

6/12MP Infrared Outdoor IP 360-degree Fisheye Camera
SAFETY
When installing your Ax78R/98 camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• sources of powerful electromagnetic radiation such as radios or TV transmitters
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light
• unstable light sources as this may cause flickering
• temperatures below -30° Celsius or -22° Fahrenheit and above 60° Celsius or 140°
Fahrenheit.
POWER SUPPLY
Ax78R/98 Power consumption requirement: DC 12V / PoE (IEEE 802.3af).
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty. PoE power is supported.
CLEANING
• For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,
dry cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened with a
small quantity of neutral detergent, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finishes.
SERVICING
To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the
camera. Refer servicing to qualified personnel only.
PACKAGE CONTENTS
Ensure that the items received match those listed on the order form and the packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing box
includes:
A. Waterproof RJ45 connector (pre-assembled) x1. Use to protect RJ45 connector from
the moisture.
B. Waterproof tape x1. Use to protect DC12V power connector from moisture.
C. Plastic Anchor x4
D. Round Head Screw (Tapping Type) x4
E. RJ45 standar connector x2
F. Surface Mount template x1
Waterproof tape
e Waterproof tape
pe Waterproof ta
f tape Waterproo
oof tape Waterpr
proof tape Water
A B C
Scan this QR code or visit ftp.i3international.com
download AnnexxusConfigurationTool v1.5 (ACT) and the
full User Manual. Use the ACT v1.5 or higher to set Ax78R/98
administrative password and IP address.
Contact our Technical Support team at: 1.877.877.7241 or
support@i3international.com
if you have any questions or
concerns regarding camera installation or if you require software
services or support.
i3-TRNG-CAMS-Ax78R/98-QSG.indd
1
TOP
Drill Template
Hole A : for cables routed through
the ceiling
Screw hole 1 : for Mounting Base
1
F
D E
to view and
QR Code to Full
User Manual / ACT
CAMERA PARTS AND DEFINITIONS,
DISASSEMBLING THE CAMERA
Ax78R/98 Camera Side view,
with camera cover attached
Ax78R/98 Camera, Top view, with camera
cover attached. Lift the safety lock screw cover
to reveal the safety lock screw (i). Use a Phillips
screwdriver to loosen the lock screw, then grip the
camera cover and flex on one side, towards the center.
Lift UP to remove.
iii
iv
v
Camera module with camera cover removed.
Use a Phillips screwdriver to remove the SD card panel cover (ii).
to expose microSD card slot (iii) and the RESET pin hole (iv).
Rubber gasket is provided for an airtight seal and moisture protection (v).
CAMERA RESET
To reset camera to factory defaults (incl. IP address and user management), unplug
the network cable. Then use a sharp object to press the RESET button, re-connect the
network cable and continue pressing the RESET button for 10 seconds. The camera will
be rebooted and reset to factory defaults.
1
1
2
3
4
Camera module with camera cover removed.
Quick Start Guide
Ax78R/98
ii
1. Built-in speaker
2. MicroSD card slot and
5
RESET pin hole.
6
Insert a micro SDHC card
for backup/emergency
7
recording and/or storage.
3. Light sensor for day/night
switching
4. IR LEDs x3
8
5. Camera cover lock screw
hole
6. Mounting screw hole/
slot x3
7. Camera cover clips x3
8. Built-in microphone
9
9. DC12V Power connector
10. RJ45 Network connector
10
(PoE supported)
FW v.5.4.5;
i
Rev. 190305