Advertisement
22000 Suite 250 Industrial Blvd, Rogers, MN 55374 / 1-866-527-7637
Polaris PRO XP Winch Mount
Thank you for purchasing our VIPER winch mount. You now own a premium custom
winch mount which allows you to use your winch with your UTV / SxS. Please note the
following instructions and heed all warnings.
• Please use common sense when operating your UTV / SxS
• Read your Winch Operators Manual and all other operator manuals, including
warning labels, before operating your UTV / SxS
• Be observant of moving parts causing entanglement, use extreme caution!
SEVERE INJURY OR DEATH MAY RESULT IF YOU ARE NEGLIGENT.
866.527.7637
www.motoalliance.com
VIPER Winch Mount
MA11941
1
motoinfo@motoalliance.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Motoalliance VIPER MA11941
Summary of Contents for Motoalliance VIPER MA11941
- Page 1 22000 Suite 250 Industrial Blvd, Rogers, MN 55374 / 1-866-527-7637 www.motoalliance.com VIPER Winch Mount MA11941 Polaris PRO XP Winch Mount Thank you for purchasing our VIPER winch mount. You now own a premium custom winch mount which allows you to use your winch with your UTV / SxS. Please note the following instructions and heed all warnings.
- Page 2 MA11941-2 Fairlead Plate MA11226-1 (only for use with a standard spool winch) 7/16” Flat Washer 7/16”-14 x 1.5” Hex Head Bolt 7/16”-14 Nylock Nut M10-1.5 x 25mm Socket Head Bolt (only for use with a standard spool winch) Figure 1 866.527.7637 Motoinfo@motoalliance.com...
- Page 3 1. Using a T40 torx bit, remove the front facia and set the hardware aside for future use. Figure 2 2. Using a T40 torx bit remove the front plate from the facia. Figure 3 3. Replace the front plate with MA11941-2 using the hardware removed in Step 2. Figure 4 866.527.7637 Motoinfo@motoalliance.com...
- Page 4 Figure 5 5. Using a 13mm socket, remove the front bumper from the supports. Set this hardware aside to use later. Figure 6 6. Using the hardware supplied with your winch, install the winch and fairlead onto MA11941-1. 866.527.7637 Motoinfo@motoalliance.com...
- Page 5 Note: If you have a standard spool winch (3” x 4.875” bolt pattern) use MA11226-1 as a back plate. Otherwise, set aside and do not use. Figure 7 7. Install the front bumper onto MA11941-W1 using the hardware set aside earlier. Figure 8 866.527.7637 Motoinfo@motoalliance.com...
- Page 6 11. Verify that the winch and mount and square and secure and tighten down all hardware. 12. Follow the instructions for wiring up your winch included in your winch manual. 13. Most installations will use the OEM contactor mounting location on the passenger’s side firewall. 866.527.7637 Motoinfo@motoalliance.com...
- Page 7 14. Reinstall the front fascia over the winch mount. 15. Recheck and tighten down all hardware after the first couple times driving your machine and before every winching season as the frame may have flexed causing the hardware to loosen. 866.527.7637 Motoinfo@motoalliance.com...
Need help?
Do you have a question about the VIPER MA11941 and is the answer not in the manual?
Questions and answers