HMS LOOP12 User Manual page 22

Table of Contents

Advertisement

Available languages

Available languages

Eight.Treadmill Simple method of troubleshooting
Fault or phenomenon
No display on the treadmill.
Treadmill display not complete,some
words are missing.
Treadmill operation not smooth,weak or
shake.
---or----(or display E00/E07
according to the request of the
customer)
E01-communication fault(driver
doesn't recieve meter signal);
E13-communication fault(Meter
doesn't recieve driver signal)
E02-Stalling
protection(Explosion-proof prot
Meter
ection or main motor fault)
display
E03-No
speed
signal(with speed sense driver)
E04-Incline
self-checking
learnning fail(with incline driver)
E05-Overcurrent protection
E06-Usually it is because
motor has a open circut
E08-storage 24C02 fault(with
external 24C02 driver)
E09-Reverse error(with reverse
driver)
Meter
E10-Usually due to motor
display
instant peak current
abnormal,over current
protection
E11-External AC volatge over
voltage(according to the
request of the customer)
E14-External AC voltage
undervoltage(according to the
request of the customer)
Cleaning
Please make sure the treadmill's power plug is pulled out before cleaning or maintaining the product.
Keep treadmill clean by dusting regularly. Be sure to clean the exposed part on both sides of the running belt , which can reduce the piling of dust
under the running belt. Make sure the shoes are clean , avoid to take foreign material to under the running belt to wear off the running belt and
running board. The top of the belt need to be cleaned with a wet, soapy cloth. Be careful to keep liquid away from the electrical components and
underneath the running belt.
WARNING
Remember to unplug the treadmill from the electrical outlet before removing the motor cover. Remove the motor cover and vacuum under the
motor cover at least once a year.
Possible reason
A. Power not connected, or no power.
B. Power switch is not turned on.
C. Driver is without power or damaged.
D. Meter signal wire has open circuit.
E. Meter damaged.
F. (LCD)backlight not on.
A .Display driver IC has dry joint or connection welding.
B. (LCD)bus bar slip,not fastened fully.
C. Display driver IC fault.
A .There is resistance in the transmission part.
B Transmission belt too tight or too loose.
C .Driver torsion strength too small or too big.
A .Safety key fall off.
B .Magnetron is not connected rightly.
A .Meter signal wire not plugged well or has a poor contact.
B .Meter signal wire has short circuit because of damage
or has open circuit.
C. Meter signal circuit fault.
D. Diver signal circuit fault.
A .Motor wire is not plugged well,or there is open circuit
inside the motor.
B. Driver IGBT breakdown and damaged.
C. External AC voltage too low.
A .Speed signal wire not plugged well,or sensor is damaged.
sensor
B .Driver sense line fault.
A. Incline motor wire or signal wire not plugged well.
B. Incline motor fault.
C. Driver fault.
A.Overlaod.
B .Transmisssion part stuck or blocked.
C. There is short circuit inside the motor.
E.
Diver burned.
A .The motor wire is not plugged well.
B. There is open circuit inside the motor.
C. Motor idles away.
A .Storage IC not fully connected(not switch power).
B. Storage IC damaged,or related circut fault.
A. The treadmill is in standing position or not level.
B. Driver reverse line fault.
A .Driver has excessive torque.
B. There is short circuit inside the motor.
C. Transmission part stuck.
AC Over voltage:For 220V system,voltage higher than
270VAC;For 110V system,voltage higher than 150 VAC.
AC undervoltage:For 220V system,voltage lower than
160VAC,For 110V system,voltage lower than 70VAC.
Method to the problem
Power cord connect to alternating current,or check AC
socket.
Turn power switch to On position.
Press again the overload protector,or change driver.
Change signal wire,replug again.
Change meter.
Need repair,check backlight line ,or change backlight.
Need repair,check welding spot,reweld .
Reassemble LCD.
Need repair,weld new display driver IC.
Adjust the transmission part,or add lubricating oil.
Adjust the transmission belt tightness.
Adjust the tortion potentiometer to the right place
Put the safety key to the right plugging or inserting
place on the panel.
Assemble the Magnetron to the right position.
Replug the wire.
Change signal wire.
Change meter.
Change driver.
Replug the motor wire,or change motor.
Change driver.
Stop using,ask the electrician to do trouble shooting.
Replug speed signal wire,or change sensor.
Change driver.
Check lines connected wrong or not,replug the line.
Change incline motor.
Change driver.
System protection,if it is artificial locked-rotor then just
restart.
Adjust the transmission part,or add lubricating oil.
Change motor.
Change driver.
Replug the motor wire.
Change motor.
Send error message when the current is too low,please
assemble the treadmill to test.
Replug to IC seat,note the PIN1 foot position.
Change storage IC,or change driver.
Adjust treadmill,put it level.
Change driver.
Adjust the torsion potentiometer to proper position.
Change motor.
Adjust the transmission part,or add lubricating oil.
Stop using,ask the electrician to do trouble shooting.
Stop using,ask the electrician to do trouble shooting.
.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LOOP12 and is the answer not in the manual?

Subscribe to Our Youtube Channel

This manual is also suitable for:

Loop12 multi

Table of Contents