Table of Contents
Advertisement
The replacement saw blades are stored in the "saw blade
garage" 3, on the side of the panelling of the top arm.
The DSH/E saws soft wood up to a thickness of 2", plastic up
to 1 1/4" and non-ferrous metals up to 0.4".
The saw can also be used without problem for separating
Plexiglas, GRP , foam, rubber, leather and cork.
And so that the dust does not obscure the view of the cutting
line when working, there are automatically driven bellows with
adjustable air nozzle 7. An additional vacuum cleaner can also
be connected. The connecting piece 11 is positioned at 90° to
save space.
This guarantees clean work.
Scope of supply:
1 pc. Scroll Saw DSH/E
1 pc. connector for Vacuum cleaner
1 pc. Bag with air nozzle incl. accessories
5 pc. Saw blades 18 teeth
5 pc. Saw blades 25 teeth
1 pc. Allen key with T-handle
1 pc. Operating manual
7 Technical data
No. of strokes:
Stroke height:
Max. cutting
height (90°):
Max. cutting
height (45°):
Table tilt:
Cutting blade length:
Net weight:
Dimensions:
LxWxH
Table:
Depth of Throat:
Motor:
Voltage:
Amps:
8 Set-up and commissioning of the saw:
CAUTION:
For your own safety, do not operate your Scroll Saw until it is
completely assembled and installed according to the following
instructions!
400-1.600 strokes per min.
3/4"
2"
1"
0-45°
5" Pin-Type or Plain End (without
cross pin)
34.6 lb
20 7/8" x 10 5/8" x 11 13/16"
14 1/8" x 10 5/8"
15 3/4"
110-120 V, 60 Hz
1.6 A
Disconnect power to the machine during the entire assembly
process. Failure to do this may result in serious personal
injury.
8.1 Unpacking (fig. 1a and 1b):
Disconnect power to the machine during the entire assembly
process. Failure to do this may result in serious personal
injury.
1. Unpack the device and remove it from the box. Ensure that
the device is not lifted by the plastic panelling around the
top arm 4 (as shown on the sheet attached to the
packaging).
2. For transport reasons, the saw table is tilted up at an angle
of about 45°. Turn the toggle 10 to tilt the table back into
the horizontal position (the precise setting is described
below). Then thighten the toggle 10 again.
8.2 Attaching Blade Guard
Your DSH/E Scroll Saw is provided with the attached blade
guard. But for some of the actions and adjustments described
in this manual it could be necessary to detach the blade
guard.
Attaching and detaching the blade guard:
1. Bend up the saw blade guard on the upper side and hang it
out like shown in illustration 2a.
2. For attaching the saw blade guard just act the opposite
way around: Bend up the saw blade guard on the upper
side and hang it in. There are holes in the upper cover
designed for that.
8.3 Setting up the saw:
Safe and precise work is only possible with careful fixing!
Bolt your Scroll Sas securely to a stand or workbench. If there
is any tendency for the Scroll Saw to tip over or move during
certain operations (for example cutting long, heavy boards),
fix the Scroll Saw stand or the workbench to the floor.
1. Secure saw with two screws (not included in scope of
delivery) on a solid workbench. Use the drill holes intended
for this purpose (17, fig. 1) which are located at the front
and back of the saw base.
The saw is equipped with rubber feet for noise insulation. If
required, you can also place an additional plastic or cork
underlay between the machine and the standing surface (not
included in scope of delivery!).
NOTE:
- 11 -
Advertisement
Table of Contents
