1. Manuals
  2. Brands
  3. Original Tractor Cabs Manuals
  4. Tractor Accessories
  5. 60275
  6. Parts list & assembly instructions

Original Tractor Cabs 60275 Parts List & Assembly Instructions

Windbreak for kubota rtv 400
Hide thumbs

Advertisement

Table of Contents

WINDBREAK #60275
FOR
KUBOTA RTV 400
PARTS LIST – ASSEMBLY INSTRUCTIONS
IMPORTANT
READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE
CAUTION !
REMOVE THE VINYL PANELS FOR TRANSPORT IN AN OPEN TRUCK OR TRAILER
WARNING !
THIS CAB WILL NOT PROTECT OPERATOR FROM INJURIES CAUSED BY COLLISION, OR OTHER
ACCIDENTS
1
60275109

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 60275 and is the answer not in the manual?

Questions and answers

Related Manuals for Original Tractor Cabs 60275

Summary of Contents for Original Tractor Cabs 60275

  • Page 1 WINDBREAK #60275 KUBOTA RTV 400 PARTS LIST – ASSEMBLY INSTRUCTIONS IMPORTANT READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE CAUTION ! REMOVE THE VINYL PANELS FOR TRANSPORT IN AN OPEN TRUCK OR TRAILER WARNING ! THIS CAB WILL NOT PROTECT OPERATOR FROM INJURIES CAUSED BY COLLISION, OR OTHER...

  • Page 2: Maintenance Instructions

    WARNING 1. This cab is designed to provide foul weather protection only. It does not provide protection from noise, exhaust fumes, chemicals or injury from collision, or other accidents. 2. Do not operate machine in confined areas without proper ventilation 3.
  • Page 3 Carton Contents: Windbreak #60275 for Kubota RTV 400 Key# Part # Quantity Description 1 1/2” “U” Clamp 60287 60288 Top Support 60289 Windshield Support 60290 Front Cross Bar 60292 Door Hinge Post, RH 60293 Door Hinge Post, LH 60294-B Windshield...
  • Page 4 Step 1; See Figure 1A & 1B: Install the right and left Door Hinge Post (6 & 7). A. Remove the bolt at Reference A. Place the right Post in position as shown in Figure 1A and replace the bolt with an M10 x 35mm and M10 lock washer.
  • Page 5 Step 3; See Figure 3: Install Windshield Support (3) and Cross Bar (4). A. Use a bolt and nut to attach the Top Support to the windshield support. B. Attach the tab welded to the Cross bar to the Windshield support with a bolt and nut inserted rearward.
  • Page 6 Step 5; See Figure 5: Install the Rear Curtain snaps. A. Install the #10-32 x 1/2” Snap Bolts with the #10-32 Kep Nuts and #10 Flat Washers on each side of the holes on the lip at Reference A. NOTE: Handle the vinyl parts carefully to prevent scratching or denting the windows.
  • Page 7 IMPORTANT: Apply adhesive weather strip to the full length of the Top Support and the Windshield Support. Apply to the protruding corners where the cross tubes bolt to the side tubes of the roll bar. This will reduce wear on the vinyl at these points. Step 7;...
  • Page 8 Step 8; See Figure 8: Install the Top (10) A. Wrap the vinyl around the Roll Bar tube and secure into place with the 2” Velcro strip sewn ® inside. Repeat on the left side. B. Secure the Top to the Velcro strips on the Rear ®...
  • Page 9 Step 10; See Figure 10A, 10B, 10C & 10D: Install Doors and Door Frame, Lower right and left (14 & 15) A. Insert the top of the hinge rod into the top hinge. Lower the door down into the bottom hinge. B.

  • Page 10: Limited Warranty

    Visit us on the web to see our other products. Cabs for Lawn Tractors, Garden Tractors, Compact Tractors, Snow Blowers, Utility Vehicles, & Fork Lifts, Sun Shades for tractors, mowers & Utility Vehicles, Storage Covers for Lawn and Garden equipment. Original Tractor Cab Co., Inc.

Table of Contents