Advertisement
Quick Links
JUMBO ROPS SUNSHADE #30520 For:
Tractors and Mowers
with two post ROPS That are 2" x 2" or 2" x 3" square tube and no
more than 45" wide. Also fits 1 1/2" thick tube.
PARTS LIST – ASSEMBLY INSTRUCTIONS
IMPORTANT
READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE
CAUTION
REMOVE THE VINYL SUNSHADE COVER FOR TRANSPORT IN AN OPEN TRUCK OR TRAILER
WARNING
THIS SUNSHADE WILL NOT PROTECT OPERATOR FROM INJURIES CAUSED BY COLLISION,
OR OTHER ACCIDENTS
30520717
1
Advertisement
Related Manuals for Original Tractor Cabs 30520
Summary of Contents for Original Tractor Cabs 30520
- Page 1 JUMBO ROPS SUNSHADE #30520 For: Tractors and Mowers with two post ROPS That are 2” x 2” or 2” x 3” square tube and no more than 45” wide. Also fits 1 1/2” thick tube. PARTS LIST – ASSEMBLY INSTRUCTIONS...
-
Page 2: Tools Required
Carton Contents: Jumbo ROPS SunShade #30520 Key # Part # Qty. Description 30521 Mounting Bracket 30522 Front Bow 30523 Rear Bow 30524 Top Bow 30525 Top Bow (reduced end) 30445 Brace Tube 3/4” 30446 Brace Tube 1/2” 30526 Side Mounting Plate... - Page 3 Step 1; See Figure 1: Assemble Front Bow Halves. A. Use two 5/16” x 3/4” bolts and 5/16” flange locknuts to assemble the two Front Bows Halves as shown. Do not tighten at this time. 5/16” x 3/4” Front Bow Halves Figure 1...
- Page 4 Step 2; See Figure 2: Assemble Rear Bow Halves. A. Use two 5/16” x 3/4” bolts and 5/16” flange locknuts to assemble the two Rear Bows Halves as shown. Do not tighten at this time. Rear B w Halves 5/16” x 3/4” Figure 2 Step 3;...
- Page 5 Step 4: See Figure 4: Install Top Bow Halves and Mounting Bracket. A. Join the Top Bow Halves together. Insert 1/4”x 1 1/4” bolts with flat washers outward through the frame holes and then the holes in the flattened ends of the Top Bow Halves. Add nuts and tighten the bolts while keeping the Bow straight up and down.
- Page 6 Step 5; See Figure 5: Install and adjust the Frame. A. Place the clamps of the assembled frame on the ROPS. Insert two 1/4” x 2 3/4” up through the holes in the clamps and add locknuts. Center the assembly to the ROPS and tighten the bolts. Place a plastic cap over each bolt.
- Page 7 Step 6; See Figure 6: Install the Braces. A. Loosen the 5/16” x 1/2” bolts in the weld nuts on the large round tube and insert the small support tubes into the large support tubes. Tighten just enough to hold the tubes together. With the weld nuts pointed upward, insert a 1/4”x 1 1/4”...
- Page 8 Step 7; See Figure 7: Install the Vinyl Cover. ® A. Slip the front of the Vinyl Cover over the Front Frame. Connect the Velcro strips together. Pull ® the flap at the rear of the of the cover over the rear frame and secure it with the Velcro fastener.
- Page 9 For Replacement Parts and Accessories Contact: Original Tractor Cab Co., Inc. P.O. Box 97 6849 W. Front St. Arlington, IN 46104 Phone 765-663-2214 765-663-2101 Email Sales@originalcab.com Visit us on the web to see our other products. www.originalcab.com Cabs for Lawn & Garden Tractors, Compact Tractors, Snow Blowers Sunshades for Tractors, Mowers, &...
- Page 10 LIMITED WARRANTY SNOW REMOVAL EQUIPMENT CABS COVERED BY WARRANTY ORIGINAL TRACTOR CAB CO., INC., (the "Company") warrants to the owner that each new product listed below is merchantable and free of defects in workmanship and material. During the warranty period, the dealer from whom the product was bought, or the Company, will provide, free of charge, parts and the shipping costs of parts necessary to correct any defect in workmanship and material.
Need help?
Do you have a question about the 30520 and is the answer not in the manual?
Questions and answers