Table of Contents
Advertisement
maintenance
MAINTENANCE
INSTRUCTIONS
1. Always turn off the valve before cleaning. For
relighting, refer to lighting instructions. Keep
the burner and control compartment clean by
brushing and vacuuming at least once a year.
When cleaning the logs, use a soft clean paint
brush as the logs are fragile and easily damaged.
2. Clean glass (never when unit is hot), appliance,
louvers, and door with a damp cloth. Never
use an abrasive cleaner. The gold louvers (and
optional gold door) may be scratched if abrasives
are used to clean them.
The heater is finished in a heat resistant paint
and should only be refinished with heat resistant
paint (not with wall paint). Regency
StoveBright Paint - Metallic Black #6309.
3. Make a periodic check of burner for proper
position and condition. Visually check the flame
of the burner periodically, making sure the flames
are steady; not lifting or floating. If there is a
problem, call a qualified service person.
4. Caution: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause
improper and dangerous operation.
5. The appliance and venting system must be
inspected before use, and at least annually, by
a qualified field service person, to ensure that
the flow of combustion and ventilation air is not
obstructed.
During the annual service call, the burners
should be removed from the burner tray and
cleaned. Replace the embers but do not block
the pilot.
6. Keep the area near the appliance clear and free
from combustible materials, gasoline, and other
flammable vapours and liquids.
WARNING: CHILDREN AND ADULTS
SHOULD BE ALERTED TO THE
HAZARDS OF HIGH SURFACE
TEMPERATURE AND SHOULD
STAY AWAY TO AVOID BURNS
OR CLOTHING IGNITION. YOUNG
CHILDREN SHOULD BE CAREFULLY
SUPERVISED WHEN THEY ARE IN THE
SAME ROOM AS THE APPLIANCE.
42 |
Regency
U39-11 ULTIMATE™ Freestanding Gas Stove
®
DO NOT USE THIS APPLIANCE IF ANY
PART HAS BEEN UNDER WATER.
IMMEDIATELY CALL A QUALIFIED
SERVICE TECHNICIAN TO INSPECT
THE APPLIANCE AND TO REPLACE
ANY PART OF CONTROL SYSTEM
AND ANY GAS CONTROL WHICH
HAS BEEN UNDER WATER.
CAUTION: ANY SAFETY SCREEN OR
GUARD REMOVED FOR SERVICING
AN APPLIANCE MUST BE REPLACED
P R I O R TO O P E R AT I N G T H E
uses
®
APPLIANCE.
7. Each time the appliance is lit, it may cause
condensation and fog the glass.
condensation and fog is normal and will
disappear in a few minutes as the glass heats
up.
Never operate the appliance without the glass
properly secured in place or with the door open.
8. Periodically check the pilot flames. Correct
flame pattern has three strong blue flames: 1
flowing around the thermopile and 1 around the
thermocouple, and 1 flowing across the rear of
the burner (it does not have to be touching the
burner).
Note: If you have an incorrect flame pattern,
contact your Regency
instructions.
Top View of pilot flame
Incorrect flame pattern will have small, probably
yellow flames, not coming into proper contact with
the rear of the burner or thermopile.
GENERAL VENT
MAINTENANCE
This
Conduct an inspection of the venting system semi-
annually. Recommended areas to inspect as follows:
1. Check the Venting System for corrosion in areas
that are exposed to the elements. These will
appear as rust spots or streaks, and in extreme
cases, holes. These components should be
replaced immediately.
2. Remove the Cap, and shine a flashlight down
the Vent. Remove any bird nests, or other foreign
material.
3. Check for evidences of excessive condensation,
such as water droplets forming in the inner
liner, and subsequently dripping out the joints,
dealer for further
®
Continuous condensation can cause corrosion
of caps, pipe, and fittings. It may be caused
by having excessive lateral runs, too many
elbows, and exterior portions of the system
being exposed to cold weather.
4. Inspect joints, to verify that no pipe sections or
fittings have been disturbed, and consequently
loosened. Also check mechanical supports such
as Wall Straps, or plumbers' tape for rigidity.
Top View of pilot flame
Advertisement
Table of Contents
