9. Mount uprights to the floor per 12. Mount lower wireway covers to the 20. Clean product and site. 1. Read and review Concerto Seating the tablet option and the electrical seat back panels. 21. Walk through with installation crew Assembly Instructions.
Page 3
Detail A Tolerances for Mounting Uprights seat. Attempting to rob from an adjacent The following tolerances apply to seat may only move the problem down standard, floor-mounted Concerto. the row. They are applied to the center-to-center dimensions of the TUBE CENTERLINE FLOOR BOLT CENTERLINE uprights, e.g.
Page 4
Figure 1 Upright Installation - Standard Upright Installation - Concerto 1. Begin installing uprights to the floor 2. At locations specified for Concerto Seating Seating with Power & USB by placing the appropriate bottom full-height side covers, use a bracket 1.
Page 5
2. Install either the -20 x " or were installed in the previous step. need additional inward pressure on 1. Follow the Concerto -20 x 1 " T-30 Torx screw Rotate the backrest forward to line the mounting brackets to squeeze...
Page 6
Concerto Seating with Power & USB ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble properly, or to secure parts may result in assembly failure and personal injury.
Page 7
The flexible conduit will pass through this slot. Full-height side cover Note: Aisle light transformers installation is covered on and dimmers are available. pages 8 and 9. Contact KI Customer Service at: 1-800-424-2432.
Page 8
Concerto Seating with Power & USB ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after #8 x / ” Pan Head Self-Tap T-20 Torx Screw assembly.
Page 9
Concerto Seating with Power & USB ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble properly, or to secure parts #8 x / ”...
Page 10
Concerto Seating with Power & USB ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble properly, or to secure parts may result in assembly failure and personal injury.
Page 11
Figure 8 Decorative End Panels - Standard 2. Position an end panel retaining clip Concerto Seating as shown and tighten the Decorative end panels are not #10 screws, clamping the end panel available with power & USB, or large to the upright (Figure 8).
Page 12
Concerto Seating with Power & USB ® Assembly Instructions Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble properly, or to secure parts may result in assembly failure and personal injury.
Page 13
3. Refer to pages 5 and 10 of the floor and anchoring hardware. installation of the uprights to the Concerto Auditorium Seating with 6. Reposition the unit and secure to the Caution: Unit must be properly ADA removable base using the Power &...
Page 14
Retrofit of Power & USB 1. Remove the pivot screws and lift 2. Follow the space-planning layout Note: Upright locations specified Components To Concerto Seating the seat assembly off the pivot and position the correct number as “FL” (full-length side cover), Note: Power &...
Page 15
& USB span connector span connector “P” (45”, 48” or 51”) module module (45”, 48” or 51”) (24”) module Concerto Right Power & USB Infeed quad 8-wire 8-wire 8-wire quad 8-wire power & USB block block span connector span connector power &...
Page 16
Concerto Seating with Power & USB ® Assembly Instructions Assemble units as described herein only. To do otherwise 4-2-2 may result in instability. All screws, nuts and bolts must be tightened securely and must be checked periodically after Receptacles Gauge of...
Page 17
Concerto Seating with Power & USB ® Assembly Instructions...
Page 18
Concerto Seating with Power & USB ® Assembly Instructions...
Page 19
Concerto Seating with Power & USB ® Assembly Instructions...
Need help?
Do you have a question about the Concerto and is the answer not in the manual?
Questions and answers