System Commissioning With The Configuration Wizard - Bosch HPC 400 Installation Instructions For Contractors

§
BOSCH
5.2 System commissioning with the configuration wizard
The user interface automatically recognises which BUS nodes are
installed in the system. Configuration wizard adjusts the menu and the
factory defaults.
The system analysis may take up to one minute.
COMMISSIONING
After the configuration wizard has performed the system analysis, the
Commissioning menu is opened. The settings must be checked here
and, if necessary, adjusted and finally confirmed.
If the system analysis is skipped, the Commissioning menu is opened.
The settings listed here must be carefully adjusted according to the
installed system. Finally, the settings must be confirmed .
Further information on the settings refer to Chapter 6 starting on
page 10.
Select the corresponding country
~~~~~----------~--------------~--~------~~--------------~-----------
Buffer cylinder Is a buffer cylinder installed in the system? No I Yes
Start configuration wizard Start the configuration wizard? Yes
I
No
Select - a -dd. h- e a -t-a- p pliance ---- Which additional heat source is used? --.-
Not Installed
I
Add. electric heater In series
I
I
Add. heater with mixer only I Add. heater with
I
I
mixer in parallel I Hybrid
1 )
I
Mono mode I Sifllle energy source I Dual mode
Mixed add. heat. interface
Add. el. heater op. mode
___ _ __ _ __ __ __ __ ---l
alternative I Dual mode parallel
I
Hybrid2~
How is the mixing valve controlled for the auxiliary heater with mixerfunction? On/Off 1 0-10 V
N-
I
How is the electric booster heater to be operated?
Is heating/cooling circuit 1 installed? Where is heating circuit 1 electrically
connected?
Reduced 1.0 I Reduced 2.0 I Reduced 3.0 I
4Step
No IOn
the
heat appliance I At the module
I
Heating circuit 1 installed
Is heating/cooling circuit 1 a heating circuit without mixing valve that is No HCl on heat appfiance I No own heating
I
Config HC1 at appliance
I
I
connected to the device? circuit pump I Via pump PCl
Priority
hHtiDa
circuitl
Do the mode of operation and flow temperature in heating circoit 1 determine ; Yes l No
I how the other heating circuits are operated?
Mixer heating circuit 1 Is heating/cooling circuit 1 a heating/cooling circuit with mixing valve? Yes INo
I
Mixer runtime heat eirc. 1
I
How long does it take for the mixing valve in heating/cooling circuit 1 to rotate
T
0 ... 6005
I
from one stop to the other? I
Heating system heat eirc. 1 What type of heating does heating/cooling circuit 1 handle?
Radiator I Convector heater I Underfloor
I
Ctrl type h. circ. 1 How should the temperature influenced by heating circuit 1 be controlled? Outdoor-temp. -compensated I Outside temp.
with low end
Prog. unit Heat. circ. 1 What user interface or remote control is installed for heating/cooling circuit 1?
I
HPC400 I CR 10 I CR 10 H
Heating circuit 2 installed, ...
As for heating circuit 1
Heating circuit 3 installed, ...
r--
As for heating circuit 1
~
H'- i ~
lied -
----- ----- ----
-
---
-
- -
- -
eating c rcult Insta , ... As for heating circuit 1
,
DHWsystem
Is a DHW system installed?
--------l-
On
I
Off
t - - - - - - - -
--
- -
-
- -
- -
- - -
-
DHW heat pump 1 At which heat pump is DHW heating to be activated if two heat pumps are
On
I
Off
I
(DHW heat pump 2)
installed?
----
- - - - - - -
- t---- -- - - - ---- - -
~~-
-
----
------
DHW circ.pump installed Is a DHW circulation pump installed in the DHW system? No I Yes
f
Solar thermal sys installed Is a solar system installed? No I Yes
---
----
-
- -
- -
----
-- - -
- l
- - -- - - - -
Fixed temperature The Heating system is connected directly to the DHW cylinder and the heating
Off
IOn
I
temperature is controlled with a mixing valve. The heat pump will maintain a
I constant temperature.
105 ... 60005 Pool mixing valve Is a diverter valve installed for heating the swimming pool? How long does it
I
take for the diverter valve to switch from one end to the other?
~E _ lect
__
r~ . _ a n _ od
__
e _ i n_ cyl ~ in _ de
__ r ____
-+ ______
~_-
__
ls_ an ~ i _ ne _ rt _ a _ n~ od -_- e ~ i_ n - s~ta _ lI _ ed
__
in_ th _ e~ D~ H_ W ~ - c~ y_ l in _ d~ er? ~.
________
-+ ____________
Yes INo
~F ~ u_ s e ~ s _ iz _ e
______
~
______
~
__________
A_ t w ~ h _ a_ t c _ u_ rr ~ e~ n t~ is ~ t~ h e ~ s ~ y~ s t~ e m ~ '~ s~ f u~ s e ~ t ~ ri~ ~ ~ e_ r ro ~ ?
________
-+ ______
~ 1~ 6 ~ A ~ 1 20 ~ A ~ 12 ~ 5~A ~ 1 3~2~A~----~
Confirm configuration Do the settings match with the installed system? Confirm
I
Back _ _ _
Table 11 Settings in the Commissioning menu
1) Not available if Germany is set as the country.
2) Only available if Germany is set as the country.
The DHW system is activated by default when delivered.
If no DHW system is installed, but one is activated, the
user interface indicates a fault.
~
If no DHW system is installed in the system,
deactivate the DHW system in the Commissioning or
DHWmenu.
~PC 100-1~
'1()f;!l
fllllnl 0'
9
AI