Advertisement
Quick Links
KIT COMPONENTS
• A) Trim panel • B) Back panel • C) Radio bracket • D) Pioneer brackets • E) Panel clips (2) • F) Flat-head radio screws (8)
A
B
Metra. The World's Best Kits.
®
Mazda CX-3
2016-2020
Toyota Yaris
2019-2020
MetraOnline.com
Visit
for more detailed information about the product and up-to-date vehicle
specific applications
KIT FEATURES
• ISO DDIN radio provision †
• Pioneer modular DDIN radio provision ‡
† Kit designed for "L" shaped aftermarket radio, with chassis at bottom
‡ Pioneer radios DMH-C2550NEX and DMH-C2500NEX
C
MetraOnline.com
D
E
F
© COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
107-MZ1B
I N S TA L L AT I O N I N S T R U C T I O N S
U.S. Patent Pending
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly
–ISO DDIN radio provision .................................4-5
–Pioneer modular DDIN radio provision ......... 6-7
WIRING & ANTENNA CONNECTIONS (sold separately)
Wire harness: 70-7903L, 70-7905
Antenna adapter: 40-HD10L
Steering wheel control:
Go to AXXESSINTERFACES.COM for options
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 10mm Socket wrench
Attention!
Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
REV. 9/17/20 INST107-MZ1B
Advertisement
Related Manuals for Metra Electronics 107-MZ1B
Summary of Contents for Metra Electronics 107-MZ1B
- Page 1 When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 9/17/20 INST107-MZ1B...
- Page 2 DASH DISASSEMBLY 1. Unclip and remove the panel on the top of the dash behind the radio display. (Figure A) 2. Unclip and remove the panel on the top of the dash in front of the radio display. (Figure B) 3.
- Page 3 KIT PREPARATION 1. Attach (2) panel clips provided to the radio bracket. (Figure A) Continue to Kit Assembly (Figure A) REV. 9/17/2020 INST107-MZ1B...
- Page 4 KIT ASSEMBLY ISO DDIN radio provision 1. Secure the radio bracket to the radio using screws supplied with the radio. (Figure A) Note: Radio chassis screws must be flush. Screws are provided if needed. 2. Slide the radio bracket assembly into the dash opening.
- Page 5 KIT ASSEMBLY (CONT.) 5. Clip the panel in front of the radio to the dash. (Figure D) 6. Clip the trim panel to the back panel over the face of the radio. (Figure E) (Figure D) (Figure E) REV. 9/17/2020 INST107-MZ1B...
- Page 6 KIT ASSEMBLY Pioneer Modular DDIN radio provision Note: For step 1 reference the installation manual provided with the radio for which hardware to use. The display screen and radio chassis use two different types of screws. 1. Secure the Pioneer chassis and display screen to the Pioneer brackets using (8) screws supplied with the radio.
- Page 7 KIT ASSEMBLY (CONT.) 4. Slide the radio bracket assembly into the 7. Clip the panel in front of the radio to dash opening. The rear of the bracket the dash. (Figure F) should go into the rear support slot in 8.
- Page 8 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 9/17/20 INST107-MZ1B...