Contents 1. Attention ......................- 3 - 2. Introduction ......................- 6 - 3. Main Features ..................... - 6 - 4. The Product ......................- 6 - 5. Connect the Camera .................... - 7 - 5.1. How to Connect a Camera ................- 7 - 6.
1. Attention ■ About this manual 1.Before using the camera, please read this manual thoroughly. 2.Please keep this manual reachable and always refer to the contents when needed. 3.Please contact us if the manual is lost or damaged. We will provide a replacement. 4.We cannot guarantee the safety of improper uses of the camera.
Page 4
■ For Safe Use Warning ●In following circumstances, please stop using the product and turn off the power immediately to prevent the risks of fires and electric shocks. If the product is defective, please contact us for repair or exchange. For your safety, please do not disassemble, modify or repair the camera on your own. Please stop using the product and turn off the power immediately when: ・The product becomes smoky or gets extremely hot on the surface, or makes unusual smells or sounds.
Page 5
For more details, please refer to the sites below: Hardware Warranty: http: //www.artray.us/download/artray_warranty.pdf ■ Dispose To dispose this product, please return the camera to us. If you decide to dispose the camera without returning it us, please follow related regulations and have the camera disposed as an industrial waste.
The InGaAs sensor can detect radiation invisible to human eyes and CCD/CMOS cameras in the wavelength range between 400 nm to 1700 nm bond. ●High Resolution, High Frame Rate ARTCAM-990SWIR-TEC uses a higher resolution sensor of 1280 x 1024 pixel and delivers image at 72 fps. ●USB3.0 Interface This camera adopts USB3.0 interface, so the data can be delivered to PC directly.
6. Specifications 6.1. Camera Specification ARTCAM-990SWIR-TEC MODEL 1.3MP InGaAs Image Sensor Sensor Type USB3.0 Bulk Transfer Interface 12bit Output Bit Depth 72fps (12bit) Frame Rate 20.3 µsec. ~ 2sec. Shutter Speed Internal Synchronization Synchronization System C Mount Lens Mount HR10A-7R-6S(73) (HIROSE)
6.1.1. Analog / Digital Gain Settings ARTCAM-990SWIR-TEC is compatible with analog and digital gain. Setting value of gain on software can be set from 0 ~ 420, and the gain will change from 0.0dB ~ 42.0dB accordingly. G a i n can be calculated by the following formula: G a in[dB] = value / 10.0[dB]...
Sensor Position and the Light Receiving Surface 6.1.4. H = 5[um] * 1280 = 6400 [um] V = 5[um] * 1024 = 5120 [um] 6.1.5. Field of Vision: Lens versus Sensor(For Reference Only) ※ The ratios of sensor size (diagonal) to lens size in the above illustrations are as follows: 1/2 inch = φ8mm, 2/3 inch = φ11mm, 1 inch = 15.8mm.
6.3. Camera Function The functions of the camera are as follows. DEFAULT ITEM RANGE REMARKS VALUE Shutter Speed 20.3[µs]~2[s] 1[ms] G a in 0~420 G a in [dB] = Value/10 (Analog/Digital) (0~42[dB]) (0[dB]) ROI, ROI: Vertical only Sub-sampling ON/OFF (Horizontal only available on software) (1/2) Sub-sampling: 1/2 Trigger...
7. System Requirements 7.1. Recommended System Requirements ●Host Controller This camera is applicable to USB 3.0. Connecting to USB 2.0 host controller may cause low-speed or failure to function properly. ●CPU The driver of this camera is applicable to computer architecture “x86” or “amd64”. The specification of CPU effects directly the imaging process speed, therefore it is highly recommended to utilize a high-end CPU if possible.
Page 17
ARTRAY Co., LTD. Obtained ISO 9001: 2015 2018/9/17 1-17-5 Kouenjikita, Suginami-ku, Tokyo 166-0002 Japan TEL: +81-3-3389-5488 FAX: +81-3-3389-5486 Email: sales@artray.us URL: www.artray. us - 17 -...