Subscribe to Our Youtube Channel
Related Manuals for Ayra UV LED Brick
Summary of Contents for Ayra UV LED Brick
- Page 1 UV LED Brick LED Blacklight Bar User Manual The information in this user manual is subject to change at any time without notice. Version: 1.0 Date of creation and author's initials:07-10-2019 RV Revision date and author's initials: -...
- Page 2 Introduction Thank you for purchasing the Ayra UV LED Brick. This versatile spot armature features powerful UV modules, providing you with a high light output. This ensures a perfect blacklight effect based on LED technology. This manual provides all the information you need to know about the product before you start using it.
-
Page 3: Safety Instructions
Safety Instructions WARNING! Keep this device away from moisture, water and rain to avoid the chance of electric shocks. WARNING! Only connect this device to a suitable power socket. This device functions on a specific power voltage. If it is plugged into a power socket with a different voltage, it could result in permanent damage and even dangerous situations such as fire or electric shocks. - Page 4 - Should the device not be used in the manner described in this user manual, damages or even injuries could occur. Ayra cannot be held responsible for any injuries or damages that occur as a result of improper use of this product.
- Page 5 Only suitable for indoor use: this product was only designed for indoor use. The maximum environmental temperature must not exceed 40 degrees Celsius (104 degrees Fahrenheit). Contact: Ayra professional lighting products Verrijn Stuartweg 18 4462 GE Goes The Netherlands Please do not send any products to this correspondence address.
- Page 6 Overview and Operation Guidelines for this Device Light output Suspension bracket Safety eyelet IEC C14 power input with fuse holder LED display with menu buttons DMX input via 3-pins XLR DMX output via 3-pins XLR The information in this user manual is subject to change at any time without notice. Version: 1.0 Date of creation and author's initials:07-10-2019 RV Revision date and author's initials: -...
- Page 7 During startup, ‘AYRA’ will be shown on the display, which means the device is not ready to be operated. Once the device has fully started up, it will jump to the last-used mode. Operation modes and other settings shown on the display can now be adjusted or changed by means of the menu buttons.
- Page 8 SOUN: This device can be used in sound-controlled mode to show different effects depending on the beat it registers. The sensitivity can be adjusted when activating this mode. The higher the sensitivity value, the more sensitive the internal microphone becomes. Operating Modes The following overview is designed to show the differences between the various operation modes that are supported by the above-mentioned menu functions.
- Page 9 Upright use If you wish to use the UV LED Brick in upright position, ensure the device is placed on a stable surface like a table, DJ booth or bar. The UV LED Brick has not been equipped with rubber feet, so make sure it can’t topple over when someone trips over its cables.
- Page 10 DMX terminator In DMX mode, it’s standard practice to place a terminator at the end of a DMX circuit. A DMX terminator is an electrical termination consisting of a 120 Ohm resistor, that’s placed between the second and third pin to eliminate possible data reflections.
- Page 11 DMX Lighting Troubleshooting If you have a problem with your DMX light effect, please consult the troubleshooting section for possible solutions. If, after consulting this section, the problem remains unresolved, please contact your dealer for more information and/or help. This troubleshooting section contains information on how to solve the most common DMX light effect problems, but it does not and cannot cover every eventuality.
- Page 12 Signal loss or interference in the Close the DMX circle with a DMX circle terminator or connect a booster after maximum 32 fixtures. The device does not respond well Wrong DMX-channel mode Check to see if the correct DMX to DMX-commands. channel mode is set.
-
Page 13: Technical Specifications
Technical Specifications - UV LED bar with 9 powerful UV LEDs - 9x 3W UV LED - Metal housing - Included U-shaped suspension bracket - Various operating modes, including stand-alone - Sound-controlled mode with adjustable sensitivity - Master / Slave functionality - 1 or 2 channel DMX mode - Fitted with a safety-eyelet - Power input via IEC C14 power connector with fuse holder...
Need help?
Do you have a question about the UV LED Brick and is the answer not in the manual?
Questions and answers