Ergonomic adjustable laptop sit stand desk converter (2 pages)
Summary of Contents for StarTech.com STNDTBLT1FS
Page 1
Lockable Floor Stand for iPad STNDTBLT1FS *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.startech.com/STNDTBLT1FS.
Table of Contents Introduction ....................1 Product diagram ............................1 Tablet holder dimensions........................1 Tablet stand dimensions ........................2 Tablet base dimensions .......................... 2 Package contents ............................3 Installation requirements ........................4 Assembly ....................4 Assemble the base ............................ 4 Attach the tablet holder to the pole ....................6 Assemble the tablet holder ........................
Introduction The STNDTBLT1FS is a rugged and durable fixed-height tablet stand that you can use as a stand-alone kiosk or as an informational display. The tablet stand features a lockable tablet holder for increased security, and a base that you can screw into the floor to create a stationary holder.
Package contents Tablet holder Keys Base Qty: One Qty: Two Qty: One Base connector Connecting block Pole Qty: One Qty: One Qty: One Rubber feet M6 screws M4 screws Qty: Four Qty: Eight Qty: Four Allen key Anchor screws Anchors Qty: One Qty: Four Qty: Four...
Installation requirements • The STNDTBLT1FS is designed for 9.7 in. iPad, iPad Air, and iPad Pro tablets. • A USB charging cable at least 6 feet in length. • A Phillips screwdriver. • A drill with a 1/4 in. drill bit (if you attach the tablet stand to the floor).
Page 7
2. Run the USB cable that you intend to use to supply power to the tablet through the pole (6) (figure 2). figure 2 Pole Bottom end of pole USB cable 3. Insert the four countersunk M6 screws (8) through the holes on the bottom of the base, into the base connector (4), and into the pole (figure 3).
Attach the tablet holder to the pole 1. Place the connecting block (5) on top of the pole (6) so that the four holes on the connecting block line up with the four holes in the pole. 2. Insert the remaining four M6 screws (8) through the connecting block and into the pole (figure 4).
Page 9
figure 5 Tablet holder Connecting block Pole USB cable (sold separately) 5. Place the tablet holder (1) on top of the connecting block so that the four holes on the tablet holder line up with the four holes on the collecting block. Note: You can attach the tablet holder in a portrait or a landscape position.
Assemble the tablet holder The tablet holder is designed for iPad, iPad Air, and iPad Pro tablets, however, you can use the foam pads and blocks in order to fit other types of tablets. The opening in the tablet holder measures 198 mm by 149 mm. iPad If you intend to use an iPad in the tablet holder, place the foam pads and blocks in the formation described below.
Page 11
3. Remove the backing from three of the foam pads (13). 4. On the left side of the tablet holder, stick two of the foam pads to the inside of the metal tabs. 5. On the right side of the tablet holder, stick one of the foam pads to the inside of the metal tab (figure 9).
Page 12
When you’re done affixing the pads and blocks, the tablet holder should look like this: iPad Air and iPad Pro If you intend on using an iPad Air or an iPad Pro in the tablet holder, place the foam blocks in the formation described below. 1.
Page 13
figure 12 Tablet holder 3. Remove the backing from the six foam blocks (14). 4. On the left side of the tablet holder, stick two of the foam blocks to the inside of the metal tabs. 5. On the right side of the tablet holder, stick one of the foam blocks to the inside of the metal tab.
To avoid scratching the surface of the tablet, handle the tablet carefully when you insert it into the tablet holder. The weight capacity of the STNDTBLT1FS is up to two pounds. 1. If the tablet holder (1) is locked, use one of the keys (2) to unlock the tablet holder and open the front panel.
Pole Attach the tablet stand to the floor You can secure the STNDTBLT1FS to the floor or leave it as a free-standing tablet stand. To attach the tablet stand to the floor, complete the following: 1. Place the tablet stand where you want it to go.
Page 16
3. Use a drill to drill 1/4 inch holes in the areas that you marked with the pencil. 4. Hammer the four anchors (12) into the holes that you drilled. 5. Place the tablet stand so that the four holes on the base are on top of the anchors. 6.
Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Page 18
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom and Taiwan servicing a worldwide market.
Need help?
Do you have a question about the STNDTBLT1FS and is the answer not in the manual?
Questions and answers