Epson PowerLite 410W User Manual

Epson powerlite 410w: user guide
Hide thumbs


Table of Contents
Multimedia Projector
User' s Guide


Table of Contents

  Related Manuals for Epson PowerLite 410W

  Summary of Contents for Epson PowerLite 410W

  • Page 1 PowerLite 410W ® Multimedia Projector User’ s Guide...
  • Page 2: Important Safety Information

    Epson product. Epson is not responsible for any use of this information as applied to other products. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to...
  • Page 3: Table Of Contents

    Unpacking the Projector......10 Projector Parts ........11 Additional Components .
  • Page 4 Adjusting the Volume ......43 Shutting Down the Projector ......44 Using the Remote Control Controlling the Picture and Sound.
  • Page 5 Cleaning the Lens ....... . 74 Cleaning the Projector Case ......74 Cleaning and Replacing the Air Filter .
  • Page 6 Opening and Closing EMP Monitor ....98 Registering a Projector ......99 Monitoring Your Projector .
  • Page 7: Welcome

    Images are displayed at a native resolution of 1280 × 800 pixels (WXGA) in a wide-screen 16:10 aspect ratio. Epson 3LCD technology ensures accurate color and remarkable saturation, even in well-lit rooms. The projector’s ground-breaking short-throw lens is ideal for wall mounting, allowing more space for your class or audience, with no shadow cast by the presenter or light in the presenter’s eyes.
  • Page 8: Getting The Most From Your Projector

    You can connect up to four devices to the projector at the same time. With the projector’s identify your input source. Just press the button until you see the image you want on the screen. To prevent unauthorized use of the projector, you can assign a password, create a user logo which is displayed at startup to identify the projector, and disable the projector’s buttons through a full or...
  • Page 9: Using Your Documentation

    Epson support. If you still need help after checking this User’s Guide and the sources listed above, you can use the Epson PrivateLine Support service to get help fast. Call (800) 637-7661 and enter the PIN on your PrivateLine Support card.
  • Page 10: Registration And Warranty

    In addition, Epson offers Extra Care charge. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada, usually within one business day.
  • Page 11: Projector Parts

    Projector Parts Front Control panel Lamp cover Air exhaust vents Remote control Front adjustable sensor foot Back S-Video port LAN port Video port Remote control sensor Speaker Audio Out Monitor Out port port (for Computer1 port output only) Bottom Mounting...
  • Page 12: Additional Components

    To receive a component video signal from a VCR or other video device, you need a D-sub, 15-pin, component-to-VGA video cable, which is available for purchase from Epson. See page 13. Some older PowerBooks and Macintosh desktop models may need a Macintosh video adapter; see your computer dealer. Older...
  • Page 13: Optional Accessories

    Optional Accessories To enhance your use of the projector, Epson provides the following optional accessories: Product Short-throw projector wall mount Replacement lamp Air filter set (includes 2 filters) Replacement remote control Presentation remote control Component-to-VGA video cable S-Video cable Distribution amplifier Duet ™...
  • Page 14 Welcome...
  • Page 15: Setting Up The Projector

    Setting Up the Projector his chapter tells you how to set up the projector and connect it to a computer or video source. You can connect up to four devices simultaneously: four video sources, or two computer and two video sources.
  • Page 16: Positioning The Projector

    Projection Distance Ideally, you should place the projector between 26 to 48 inches (66 to Calculator program from 122 cm) from the screen. Use the illustrations and tables below to the Drivers &...
  • Page 17 (14 cm) 6.3 inches (16 cm) 7.2 inches (18 cm) Offset (B) 5.5 inches (14 cm) 6.4 inches (16 cm) 7.3 inches (19 cm) 8.2 inches (21 cm) 9.1 inches (23 cm) 10.3 inches (26 cm) Setting Up the Projector...
  • Page 18: Whiteboard Installation

    Do not set the projector next to loose papers that could block the vents on the sides of the projector. Make sure the projector is within 14.8 feet (4.5 m) of a grounded electrical outlet or extension cord.
  • Page 19: Other Installations

    To mount the projector on the wall or attach it to a whiteboard, you’ll need an optional short-throw wall mounting system. (See page 13 for ordering information.) You’ll also need to select Projection option in the Extended menu. See page 62 for details.
  • Page 20: Connecting To A Computer

    Connecting to a Computer You can connect the projector to any computer that has a standard note VGA or BNC monitor port, including PC notebook and laptop If you have an iBook with computers, Macintosh PowerBooks and iBooks, and hand-held an RCA video-out port, devices.
  • Page 21 If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 36 for instructions. If more than one device is connected to the projector, select the correct source after projection starts by pressing the button on the projector or remote control.
  • Page 22: Connecting With A Vga-5Bnc Cable

    If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 36 for instructions. If more than one device is connected to the projector, select the correct source after projection starts by pressing the button on the projector or remote control.
  • Page 23: Connecting An External Monitor

    This lets you view images on your computer monitor while the projector is in standby mode (plugged in but not turned on) and check your presentation or switch between picture sources even if you’ve pressed the...
  • Page 24: Playing Sound Through The Projector

    Playing Sound Through the Projector You can connect a commercially available 3.5 mm stereo mini-jack audio cable to take advantage of the projector’s built-in speaker. You can obtain the audio cable from a computer or electronics dealer. 3.5 mm stereo mini-jack audio cable 1.
  • Page 25: Connecting External Speakers

    Connecting External Speakers You can output sound to external speakers with built-in amplifiers. When you play sound through external speakers, the projector’s built-in speaker is disabled. 1. Locate the appropriate cable to connect your speakers. Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end.
  • Page 26: Connecting To Video Sources

    For composite video, use a commercially available RCA A/V cable. See page 27. For S-Video, use the S-Video cable supplied with your video device or order one from Epson. See page 28. For RGB video, use the VGA computer cable included with the projector. See page 29.
  • Page 27: Connecting A Composite Video Source

    If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 36 for instructions. If more than one device is connected to the projector, select the correct source after projection starts by pressing the button on the projector or remote control.
  • Page 28: Connecting An S-Video Source

    You’ll need an note S-Video cable, which is usually provided with your video source, or Component video provides you can purchase one from Epson (part number ELPSV01). See the highest quality video page 13 for ordering information. image. See page 30 for details.
  • Page 29: Connecting An Rgb Video Source

    Connecting an RGB Video Source Follow these instructions to connect the projector to a video player or satellite receiver that has an RGB video output port using the VGA computer cable that came with the projector. Before starting, make sure the projector and your DVD player or other video source are turned off.
  • Page 30: Connecting A Component Video Source

    If your video source has component video connectors, you can use them to project a higher quality video image than composite or S-Video. You’ll need a component-to-VGA video cable, which can be purchased from Epson (part number ELPKC19). See page 13 for Component-to-VGA ordering information.
  • Page 31: Playing Sound Through The Projector

    Playing Sound Through the Projector The projector has a built-in speaker with a maximum output of 10 W. You can play sound from your video equipment through the projector’s speaker if your video device has an audio output port. For RCA-Type Audio Output Ports Most video devices have an RCA-type audio output port.
  • Page 32 (3.5-mm stereo miniplug to two male RCA plugs) to connect to the projector. If your video device is connected to the port, you can connect a commercially available 3.5 mm stereo mini-jack audio cable to connect to the projector’s...
  • Page 33 Audio Out 4. Connect the other end of the cable to your speakers. The projector’s internal speaker is disabled while sound is output to external speakers, but you can use the remote control to adjust the volume.
  • Page 34 Setting Up the Projector...
  • Page 35: Projecting

    Projecting nce you’ve set up the projector, you’re ready to turn it on, adjust the image, and give your presentation. Although you can operate the projector without it, the remote control lets you use additional features. See Chapter 3 for instructions on using the remote.
  • Page 36: Turning On Your Equipment

    If you turn on your connected computer or video equipment before starting the projector, the projector automatically detects and displays the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image source manually.
  • Page 37 To focus and adjust the image, see page 40. If a projected image fails to appear, see “What To Do If You See a Blank Screen” on page 38. When you’re done, shut down the projector as described on page 44. Power button...
  • Page 38: Selecting The Image Source

    Make sure you’ve selected the correct image source; see the previous section. Allow a few seconds for the projector to sync up after pressing the button. Check the Signal menu to make sure the correct input source is selected.
  • Page 39 If you’re using a Macintosh laptop with Mac OS You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select Display Displays.
  • Page 40: Adjusting The Image

    If the image isn’t square, see page 42. To adjust image brightness, see page 42. If a computer image displays incorrectly, see page 43. Focus ring button on the projector to enlarge the image, or the Wide button to reduce it. Wide button...
  • Page 41: Adjusting The Height Of Your Image

    You can also change the image size by moving the projector closer to or farther away from the screen. You can use the the remote control to zoom in on a portion of the image. See page 49 for instructions.
  • Page 42: Adjusting The Image Shape

    Adjusting the Image Shape If the projector is tilted up or down, the images that are displayed will be distorted. To correct the distortion or “keystone” shape, do one or more of the following: ■ ■ You can also make keystone adjustments using the projector’s Settings menu.
  • Page 43: Correcting Computer Images

    59. Adjusting the Volume You can use the Vol– Vol+ increase or decrease the volume for the projector’s built-in speaker. A volume gauge appears on the screen while the volume is being adjusted. button on the Enter option in...
  • Page 44: Shutting Down The Projector

    63. Turn off this product when not in use to prolong the life of the projector. 4. Press up on the blue foot release lever and lower the projector to 5. Attach the lens cover. caution To avoid damaging the 6.
  • Page 45: Using The Remote Control

    20 feet (6 m) away. For example, you can turn the projector on and off, freeze the presentation, zoom in on a portion of your image, and access the menu system. (The projector menus let you adjust many projector settings;...
  • Page 46: Controlling The Picture And Sound

    You can use the remote control to select your source, adjust the colors, temporarily turn off the picture and sound, freeze the action, or zoom in on the picture. Make sure you have set up your projector and connected any equipment as described in Chapter 1.
  • Page 47: Adjusting The Color Mode

    Whiteboard Choose this fixed color mode when you need to project against a whiteboard. You can also use the projector menu system to change the color mode in the Image menu (see page 57). Color Mode Color...
  • Page 48: Turning Off The Picture And Sound

    Turning Off the Picture and Sound Press the image and sound and darken your screen. This is useful if you want to temporarily re-direct your audience’s attention without the distraction of a bright screen. To turn off the picture and sound, press the screen goes dark.
  • Page 49: Zooming Your Image

    Zooming Your Image Follow these steps to zoom in on a portion of the image: 1. Press the button on the remote control. E-Zoom + You see a crosshair indicating the center of the zoom-in area. 2. Use the four “arrow” buttons on the remote control to position the crosshair in the area you want to enlarge.
  • Page 50 ■ ■ ■ Press the options. You can also change the aspect ratio using the projector’s Signal menu. See page 58 for details. Using the Remote Control Zoom Displays images using the full width of the projection area and maintains the aspect ratio of the image. 4:3 ratio images are cut off on the top and bottom.
  • Page 51: Replacing The Batteries

    Replacing the Batteries The remote control uses two AA alkaline batteries. Follow these steps when you need to replace them: 1. Press in the tab to remove the battery cover. 2. Remove the old batteries, then insert the new ones as shown. 3.
  • Page 52 Using the Remote Control...
  • Page 53: Fine-Tuning The Projector

    ■ Customizing projector features ■ Selecting projector setup options Selecting projector network settings ■ ■ Viewing lamp usage and other information ■ Using the projector’s security features Restoring the default settings ■ button on the projector or remote control to...
  • Page 54: Using The Projector's Menu System

    See page 60. menu lets you customize the way you set up the Extended projector.
  • Page 55: Changing Menu Settings

    Changing Menu Settings Use the buttons on the remote control or on the projector to access the menus and change settings. Follow these steps: 1. Press the button on the remote control or projector to Menu display the menu screen:...
  • Page 56: Adjusting Colors And Clarity

    Press the left or right arrow buttons on the projector or the remote control to adjust a slider bar. To select from two or more settings, use the up or down arrow buttons on the projector or the remote control to highlight the desired setting, then press button to return to the previous menu or to close the menu system if you are at the main menu.
  • Page 57 Adjusts the difference between light and dark areas. (component, composite, and S-Video) ■ Color Saturation Adjusts the depth or intensity of the image colors. to set the Enter note You can also select brightness mode in the Settings menu. See page 61. Fine-tuning the Projector High...
  • Page 58: Adjusting The Input Signal

    4. When the image is set correctly, press Adjusting the Input Signal Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to manually select it. You can also change the position of the projected image, correct tracking and sync, and change the aspect ratio to widescreen format.
  • Page 59 (computer images) ■ Sync Corrects fuzziness or screen flicker by synchronizing the projector with the tracking signal sent from the computer. See page 88 for more information. ■ Position Use the arrow buttons to move the image on the screen left, right, up, or down.
  • Page 60: Customizing Projector Features

    4. When you’re finished, press Customizing Projector Features The Settings menu lets you customize the way you use the projector, from adjusting lamp brightness and speaker volume to applying security controls. 1. Press the 2. Select the 3. Press Fine-tuning the Projector (composite and S-Video) ■...
  • Page 61 ( Power operate the projector from the remote control. Changes to this setting take effect after you restart the projector. (After you turn off the projector, wait for the P a steady orange before turning it on again.) ■...
  • Page 62: Selecting Projector Setup Options

    Selecting Projector Setup Options Use the Extended menu to customize the way you set up the projector. You can configure the projector for rear and/or ceiling/wall-mounted projection, change the language for the menus and messages, set the screen background color, capture and store a custom image or logo for the startup screen.
  • Page 63 ■ Standby Mode Select to allow the projector to be monitored Network On over a network when the projector is in standby mode (the light is orange). Power ■ Language Select the language to be used for the projector menus.
  • Page 64: Selecting Network Settings

    Selecting Network Settings For information connecting the projector to a network and monitoring the projector over a network, see “Monitoring the Projector Over a Network” on page 93. Viewing Lamp Usage and Other note Information You can make changes to many of the signal settings on the Signal menu.
  • Page 65 (computer, RGB video, and component video) Sync Info Provides information that may be needed by the service technician. ■ Status Displays informations about projector problems. This information may be needed if service is required. 3. When you’re finished, press High brightness Menu...
  • Page 66: Using The Projector's Security Features

    30 times in a row, the projector is locked and you’ll need to note contact Epson to unlock it. See “Where To Get Help” on page 91. If you should happen to If someone else will be using the projector for awhile but you want to...
  • Page 67: Creating Your Own Screen Logo

    Follow these steps to capture the image and transfer it to the projector: 1. Display the image you want to use on the projector. You can use an image from a computer or video source, such as a DVD player.
  • Page 68: Setting A Password

    Save image as user’s logo? and press . Saving the logo takes a few moments. Do Enter not use the projector or other sources (computer, video, etc.) while the logo is being saved. When you see the message , press Completed...
  • Page 69: Turning On The Password And User's Logo

    3. To enable your screen logo, select . Select then press Enter When this feature is on the logo appears whenever the projector is turned on (if the Startup Screen menu; see page 62) and as the A/V Mute screen (if you selected...
  • Page 70: Starting The Projector With A Password

    If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson for service. If you have forgotten the password, contact Epson with the request code number that appears in the Password Protect Release screen for assistance.
  • Page 71: Disabling The Projector's Buttons

    Menu Installing Security Locks You can install two different types of security locks on the projector: You can use the security slot on the base of the projector to install ■ a Kensington Microsaver Security System. See page 13. You can use a wire lock to secure the projector to a room fixture ■...
  • Page 72: Restoring The Default Settings

    Restoring the Default Settings The Reset menu lets you return most projector menu settings to their note default values. It also lets you reset the lamp hours to their initial The Computer Input (1 and default value; see page 79 for instructions on resetting the lamp timer.
  • Page 73: Maintenance And Transportation

    You may need to clean the air filter and air vents. A clogged air filter the projector, turn it off and unplug the power cord. or air vent can block ventilation needed to cool the projector and Never open any cover on the cause overheating.
  • Page 74: Cleaning The Lens

    Cleaning and Replacing the Air Filter Your projector includes an air filter to ensure the best performance. If dust collects on the air filter or vent on the side of the projector, clean them as described below. Dust clogs prevent proper ventilation and can cause overheating and damage the projector.
  • Page 75 1. Turn off the projector, allow it to cool down, and unplug the power cord. 2. To clean the filter and vent, Epson recommends using a small vacuum cleaner designed for computers and other office equipment. If you don’t have one, gently clean them using a very soft brush (such as an artist’s paintbrush).
  • Page 76: Replacing The Lamp

    Turn off this product when ■ not in use to prolong the life of the projector. Contact your dealer or call Epson at (800) 463-7766 for a replacement lamp. Request part number V13H010L42. Follow these steps to replace the lamp: warning 1.
  • Page 77 3. Use the screwdriver included with the replacement lamp or a #2 Phillips-head screwdriver to loosen the screw holding the lamp cover (the lamp cover is located on top of the projector). 4. Slide the cover out, then lift it off.
  • Page 78 Push the lamp down firmly where the label appears. PUSH covered, and the top of the cover should be flush with the top of the projector.) Then slide the cover closed and tighten the screw.
  • Page 79: Resetting The Lamp Timer

    You must reset the lamp timer after replacing the lamp to clear the warning message. Follow these steps: Replace the Lamp 1. Connect the power cable and turn on the projector. 2. Press the button on the remote control or projector and...
  • Page 80: Transporting The Projector

    Transporting the Projector The projector contains many glass and precision parts. If you need to transport it, please follow these packing guidelines to prevent damage to the projector: ■ ■ note ■ Epson shall not be liable for any damage incurred during transportation.
  • Page 81: Solving Problems

    Solving Problems his chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself. This chapter explains the following: Using the projector’s on-screen help system ■ What to do when the projector’s status lights flash ■...
  • Page 82: Using On-Screen Help

    The lights on top of the projector indicate the projector’s status and let you know when a problem occurs. If the projector is not working correctly, first turn it off and unplug it. Then plug the power cord back in and turn on the projector. If this does not solve the problem, check the status lights on top of the projector and try the solutions recommended in the following table.
  • Page 83 There is a problem with the fan or a sensor. Turn the projector off and unplug it. Contact Epson for help; see page 91. There is an internal error in the projector. Turn the projector off and unplug it. Contact Epson for help; see page 91. ° ° F (35...
  • Page 84: Solving Problems With The Image Or Sound

    Power cover is removed. Also press the control to see if the picture was turned off temporarily. If the projector doesn’t turn on, the Control Panel Lock may be enabled. Press and hold the Enter 7 seconds to release the lock.
  • Page 85 Source Search projector or the remote control to select the correct source. Allow a few seconds for the projector to sync up after pressing the button. If you’ve connected a laptop computer, make sure it’s set to ■...
  • Page 86 See your software documentation for specific information. Make sure the projector isn’t placed off to one side of the screen, at an angle, or the image won’t be rectangular. Place it directly in front of the center of the screen, facing the screen squarely.
  • Page 87 Try cleaning the lens as described on page 74. Make sure the lens is not fogged by condensation. You may need ■ to wait before using the projector after moving it from a cold environment. ■ Make sure the projection distance is within the ranges described on page 16 through page 18.
  • Page 88 Press the button on the remote control to Enter/Auto automatically reset the projector’s tracking and sync settings. If necessary, you can manually adjust the settings on the Signal menu as described on page 59. To help you adjust these settings, fill the screen with a detailed image, such as a desktop background pattern or black text on a white background.
  • Page 89: Solving Password Problems

    0000 The remote control is not available. You must have the remote control to enter the password. You can purchase a replacement remote control from Epson. See page 92. A/V Mute Source Search Solving Problems...
  • Page 90: Solving Problems With The Remote Control

    You have lost the remote control. You need the remote control to access many projector features. If you have lost it, you can order another from Epson; see page 92 for details. Solving Problems Make sure you are within 20 feet (6 m) of the projector, and within range of the projector’s front or back sensor.
  • Page 91: Solving Network Problems

    Where To Get Help Epson provides these technical support services: Internet Support Visit Epson’s support website (U.S. or Canada) for solutions to common problems with the PowerLite 410W. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.
  • Page 92: Speak To A Support Representative

    Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card. This is the fastest way of speaking to a live representative, and it’s free.
  • Page 93: Monitoring The Projector Over A Network

    Monitoring the Projector Over a Network he software included with your projector lets you monitor and control your projector over a network. Use EMP Monitor (available for Windows only) to see your ■ projector’s status, switch image sources, and control basic settings.
  • Page 94: Installing The Network Software

    Installing the Network Software The network software CD-ROM includes the software you need to monitor the projector from a remote location. Windows System Requirements Before you install the software, make sure your computer meets these requirements: ■ ■ ■ ■...
  • Page 95: Connecting To The Network

    Connecting to the Network Follow these steps to connect the projector to your network and configure it with an IP address. 1. Connect the projector to your network using a commercially available 100BaseTX or 10BaseT network cable. Connect the cable to the port on the projector.
  • Page 96: Selecting Network Settings

    Selecting Network Settings Follow the instructions in this section to set up the projector’s network settings in the menu system. 1. Press the 2. Select the 3. Press Monitoring the Projector Over a Network button. Menu menu. Network . Then use the up and down arrow buttons and the...
  • Page 97: Setting Up Projector E-Mail Alerts

    Turn on to allow the projector to be detected by AMX Device Discovery-enabled software, if you are using it on your network. Setting Up Projector E-mail Alerts When this feature is enabled, the projector sends you an e-mail alert if it has any problems. 1. Press the button, select the...
  • Page 98: Using Emp Monitor

    If you want to monitor the EMP Monitor lets you use a remote computer to manage your projector while it is in projectors. It lets you easily turn the projector on or off, switch image standby mode, select sources, and check its status.
  • Page 99: Registering A Projector

    3. Click to locate projectors currently operating on the Search network. 4. Select the projector you want to add by clicking its name, then click the button. Edit 5. Enter a Display name, select a Parent group, if necessary, enter a Monitor Password, if necessary, and a Description for the projector.
  • Page 100: Using E-Mail Alerts

    7. Click the 8. When you’re done, click the If a projector experiences a problem, EMP Monitor sends an e-mail message to each of the addresses you entered in the Set mail notification function window. The subject line and body of the note message includes the projector’s name and the warning or error...
  • Page 101: Using A Browser To Monitor The Projector

    Using a Browser to Monitor the Projector If your projector is connected to a network, you can use a standard web browser to monitor and control it. When using a browser to access the projector, you cannot connect through a proxy server.
  • Page 102 Monitoring the Projector Over a Network...
  • Page 103: Technical Specifications

    Technical Specifications General Type of display Lens Resolution Color reproduction Light output (brightness) Contrast ratio Image size Projection distance Projection methods Focus adjustment Zoom adjustment Internal sound system Optical aspect ratio Zoom ratio Poly-silicon TFT active matrix F=1.8 Focal length: 6.48 mm 1280 ×...
  • Page 104: Projection Lamp

    Noise level Keystone correction angle Projection Lamp note Power consumption Lamp life results will vary depending upon mode Lamp life selected, environmental conditions and usage. Lamp brightness decreases over Remote Control time. Range Batteries (2) Dimensions Height Width Depth Weight Electrical Rated frequency Power supply...
  • Page 105: Environmental

    Up to 7,500 feet (2,286 m) with High Altitude Mode enabled; see page 62 Safety and Approvals United States FCC Part15B Class B (DoC) UL60950-1 Canada ICES-003 Class B CSA C22.2 No. 60950-1 Pixelworks projector. ™ ™ ICs are used in this Technical Specifications...
  • Page 106: Compatible Video Formats

    You can connect the projector to a wide range of computers, including PCs, Macintoshes, notebooks, and high-end workstations such as the Although images are displayed at the projector’s native resolution of 1280 × 800 pixels, Epson’s patented SizeWise chip supports computer display formats ranging from VGA through WSXGA+. Technical Specifications Refresh Rate (Hz) ®...
  • Page 107 For best results, the computer’s resolution should be set to match the projector’s native resolution (1280 × 800). If this resolution isn’t available, select one of the other compatible formats: Windows: ■...
  • Page 108 Mode XGA—60 XGA—70 XGA—75 XGA—85 XGA—120 SXGA1—70 SXGA1—75 SXGA1—85 SXGA1—100 WXGA60-1 WXGA60-2 WXGA—60 WXGA—75 WXGA—85 WXGA+ WSXGA+** SXGA2—60 SXGA2—75 SXGA2—85 SXGA3—60 SXGA3—75 SXGA3—85 SXGA+60 SXGA+75 SXGA+85 UXGA60 iMAC VGA iMAC SVGA iMAC XGA MAC13 MAC16 MAC19 MAC19-60 MAC21 * Letterbox signal ** Available only when Resolution is set to Wide in the Signal menu.
  • Page 109: Notices

    ■ Do not use the projector near water or sources of heat. ■ Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company. ■ Place the projector near a wall outlet where the plug can be easily unplugged.
  • Page 110 If liquid has been spilled into the projector, or if it has been exposed to rain or water. If it does not operate normally when you follow the operating instructions, or if it exhibits a distinct change in performance, indicating a need for service.
  • Page 111: Fcc Compliance Statement

    FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 112 Notices...
  • Page 113: Index

    Component-to-VGA video cable, 12 to 13, 26, Composite video cable, 26 to 27 Computer cable, 10, 20 to 22 connecting to projector, 20 to 24 source, selecting, 21, 22, 38, 46, 59 support, 7 supported display formats, 106 to 108...
  • Page 114 High brightness, 42, 76, 84 iBook, connecting to, 20 to 21 iMac, connecting to, 12, 20 to 22 Image capturing and saving in projector, 67 to 68 correcting shape of, 42, 60, 86 fitting on screen, 43, 59, 60, 86 focusing, 40...
  • Page 115 EMP Monitor, 98 to 100 with browser, 101 Moving projector, 80 Network connecting to, 95 managing projector remotely, 93 to 101 menu, 54, 64, 96 to 98 problems, 91 settings, 64, 96 to 98, 99 system requirements, 94 Network Protect password, 69...
  • Page 116 Resolution, 7, 65, 103, 106 to 108 Safety approvals, 105 instructions, 109 to 110 Screen logo, see User’s Logo Screen, distance from projector, 16, 103 Screens, portable, 13 Setting a password, 68 to 69 Settings menu, 54, 60 to 61 Sharpness setting, 58...
  • Page 117 90 Turning off audio, 48 picture, 48 projector, 44 Turning on password, 69 projector, 36 to 37 User’s Logo, 63, 69 Typing the password, 70 Unpacking projector, 10 User’s Logo creating, 67 to 68 displaying, 68 to 69...
  • Page 118 Index...

Table of Contents