Related Manuals for Excalibur AL-1775-3DB
Summary of Contents for Excalibur AL-1775-3DB
- Page 1 Register at caralarm.com OPERATION GUIDE AL-1775-3DB RS-475-3D al-1775-3db & rs-475-3d op guide.indd 1 8/3/16 7:41 AM...
- Page 2 REMOTE START & SECURITY PERFECTED AL-1775-3DB / RS-475-3D OPERATION GUIDE Temporary cover. Final cover is in a separate file.
-
Page 3: Table Of Contents
Table Of Contents Controller & Transmitter Overview 3 The 2-Way Controller 3 The 1-Way Transmitter 3 Controller & Transmitter Functions 3 Other Remote Start Features 8 Low Vehicle Battery Alert 8 Low Battery/Low Temp Automatic Starting 8 Turbo Timer Mode 8 Pit-Stop Mode 8 XL Pit-Stop Mode 8... -
Page 4: Controller & Transmitter Overview
Controller & Transmitter Overview THE 2-WAY CONTROLLER Controller part number: 1511-03E (w/ 2 CR2025 batteries) LOCK Call your dealer or visit www.caralarm.com to order button replacement transmitters. Controller battery replacement: UNLOCK Remove the small screw from the lower button back case, and separate the transmitter START halves Replace the batteries and button... - Page 5 Controller & Transmitter Functions (cont’d) UNLOCK / DISARM: Press and release the UNLOCK button • THE SIREN WILL CHIRP TWICE & THE PARKING LIGHTS WILL FLASH TWICE • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL FLASH THE UNLOCK LED (TWICE FOR CAR 2) AND BEEP TWICE TRUNK RELEASE / CHANNEL 2: Press the TRUNK button for 3 seconds...
- Page 6 Controller & Transmitter Functions (cont’d) • Run Time Extender: Press the START button one time during remote start to restart the engine run timer The timer will restart NOTE: This can only be used once per remote start cycle. The controller will also give you “run time expiration warning”...
- Page 7 Controller & Transmitter Functions (cont’d) PANIC: Press and hold the LOCK or UNLOCK button for 3 seconds • THE SIREN/HORN WILL SOUND, THE PARKING LIGHTS WILL FLASH, AND THE DOORS WILL LOCK OR UNLOCK DEPENDING WHICH BUTTON IS PRESSED SILENT ARM / DISARM: Press and release the TRUNK button twice in 5 seconds •...
- Page 8 Controller & Transmitter Functions (cont’d) VEHICLE TEMP REQUEST: Press and release “P” then START within 5 seconds • UPON RECEIVING CONFIRMATION, THE CONTROLLER WILL PLAY A MELODY AND FLASH THE LEDs TO INDICATE THE VEHICLE’S INTERIOR TEMPERATURE • TEMP INDICATORS: 1 LED = LESS THAN 30°F 2 LEDs = 31-60°F 2 LEDs = 61-90°F...
-
Page 9: Other Remote Start Features
Other Remote Start Features LOW VEHICLE BATTERY ALERT When your vehicle’s battery drops below 11 volts for longer than 30 seconds, the system will send an alert to the controller The controller will beep 4 times There is no visual indication The alert repeats every 30 seconds until you press any controller button This indicates that something is drawing excess power, your vehicle was parked for an extended period, or your battery health is degrading It is recommended to start your engine before the battery voltage drops below adequate cranking voltage and leaves you... -
Page 10: Manual Transmission Starting
Other Remote Start Features (cont’d) MANUAL TRANSMISSION STARTING Remote starting with a manual transmission requires that you ensure the gear selector is in NEUTRAL There are 2 available methods METHOD #1 - 3D MOTION SENSOR: This system is equipped with a 3D motion sensor built into the antenna Whenever remote start is activated, this sensor is monitored for vehicle movement If the vehicle moves just a few inches when the engine is cranking, it will instantly turn the engine off This safety feature allows you to enjoy remote start without performing reservation mode as described... -
Page 11: When The System Triggers
Security System Features (cont’d) WHEN THE SYSTEM TRIGGERS It will sound the siren/horn and flash the parking lights for 30 seconds (programmable). At this point you will also be notified on the controller as to which zone is violated (while in range) When disarming after a trigger event, the siren/horn will chirp 4 times and the parking lights will flash 4 times instead of the standard 2 times. -
Page 12: Valet Mode 11
Using The Valet Button (cont’d) VALET MODE Valet mode completely disables all security & remote start functions Keyless entry is still operable To enter valet mode, perform the following steps: STEP 1 - Disarm the system by remote or by performing an emergency override STEP 2 - Press and hold the valet switch for 2 seconds The system will chirp once and the status light will turn on EXITING VALET MODE - Press and release the valet switch once... -
Page 13: Multi-Car Operation
Multi-Car Operation The controller can operate up to 2 different systems When controlling 2 systems, it will receive all status updates on the currently selected vehicle profile and will receive only trigger alerts for the 2nd vehicle You can switch from one car to the other at anytime Use the following steps to change vehicles SELECTING CAR #1 OR CAR #2 Vehicle #1: Press the “P”... - Page 14 BLANK PAGE...
-
Page 15: Anti-Carjacking Protection
Anti-Carjacking Protection The system is equipped with two separate Anti-Carjacking protection features (ignition, open door, or both) All are programmable, and must be turned on to operate Once activated, the user has 60 seconds to cancel the Anti-Carjacking protection process (described below) If Anti-Carjacking is not cancelled, 53 seconds after being activated the siren will begin to chirp for 7 seconds to alert the user that the system is about to enter into an alarm condition The Valet Switch may still be pressed once during this period to... -
Page 16: Programming Controllers/Transmitters
Programming Controllers/Transmitters Standard Programming: Using this method to program additional or replacement transmitters does not turn on or otherwise affect the Unauthorized Transmitter Alert (UTA) feature Before you begin, have all transmitters which are to operate the system at hand and make sure the correct vehicle profile (see page 12) is selected on the controller(s). -
Page 17: User Programmable Features
User Programmable Features Feature #1 - Remote Start Run Time 3 Minutes (press LOCK to program) 10 Minutes (press UNLOCK to program) 15 Minutes (press TRUNK to program) 20 Minutes (press START to program) 30 Minutes (press LOCK & UNLOCK to program) This sets the maximum amount of time that the remote start will keep the engine running if it is not shut down by other methods Feature #2 - Flashing Light Confirmations... - Page 18 User Programmable Features (cont’d) Feature #6 - Open Door Bypass of Ignition Locking (press LOCK to program) (press UNLOCK to program) This feature cancels the automatic locking or unlocking of the vehicle’s doors if one of the doors is open when the ignition switch is turned on or off Feature #7 - Unlock w/ Trunk Release (press LOCK to program) (press UNLOCK to program)
- Page 19 User Programmable Features (cont’d) Feature #13 - SecureCode DEFAULT - 1 Press SecureCode is a unique patented feature which allows you to select the number of Valet Switch presses in two stages, instead of “1 press”, which would be required in order to perform an Emergency Override If any of the three anti-carjacking features are utilized, a customized SecureCode would also be required to turn it off once it is fully activated SecureCode operation is described on page 10...
-
Page 20: Installer Programmable Features
Installer Programmable Features This group of Installer Programmable Features are all accessed as a group in the second level of features’ programming These features have a direct affect upon the system’s op- erations related to the installation and vehicle type AND SHOULD ONLY BE CHANGED BY THE INSTALLER!!! Feature #1 - Remote Start Activation From The WHITE/BLUE Wire 1 pulse... - Page 21 Installer Programmable Features (cont’d) Feature #5 - Light Relay Function (3DB) / Sat. Port Green Wire Function (non-3DB) Dome Light Output (press LOCK to program) Start (press UNLOCK to program) Ignition Output (press TRUNK to program) Accessory Output (press START to program) Status (press LOCK &...
- Page 22 Installer Programmable Features (cont’d) Feature #10 - Turbo Timer (press LOCK to program) Run 1 Minute (press UNLOCK to program) Run 2 Minutes (press TRUNK to program) Run 3 Minutes (press START to program) This feature, the operation of which is described on page 8, when turned on configures the system to automatically keep the engine running briefly after the key is turned off.
- Page 23 Installer Programmable Features (cont’d) Feature #17 Low Temp Crank Extender (press LOCK to program) 200ms (press UNLOCK to program) 300ms (press TRUNK to program) 400ms (press START to program) When the vehicle’s interior temperature is below freezing, this feature adds extra crank time to the base timing (see installer feature #7) It applies to tachless modes only (installer feature #3) Feature #18 - Arm, Disarm or Additional Channels...
- Page 24 User Feature Programming: Ignition on, off, press valet 5 times Lock + Trunk Lock Button Unlock button Trunk button Start button # Feature Unlock + Start (Brake 1x) (Brake 2x) (Brake 3x) (Brake 4x) (Brake 5x) (Brake 6x) 1 Remote Start Run Time 3 min 10 min 15 min...
- Page 25 Back Cover Color cover is in a separate file.