Related Manuals for Excalibur AL-XX60-EDPB
Summary of Contents for Excalibur AL-XX60-EDPB
-
Page 1: Installation Guide
AL-XX60-EDPB Deluxe Keyless Entry, Security, & Remote Start System Installation Guide June 20, 2014 Temporary cover. Color cover is in a separate file. -
Page 2: Table Of Contents
Table Of Contents 6 Pin Main Wire Harness �������������������������������������������������������������������������������������������� 3 Red & Red/White Wires - Constant Power (+) Input ������������������������������������������������ 3 Pink Wire - Ignition #1 (+) Input/Output �������������������������������������������������������������������� 3 Orange Wire - Accessory (+) Output ������������������������������������������������������������������������ 4 Violet Wire - Start (+) Output ������������������������������������������������������������������������������������ 4 Pink/White Wire - Ignition #2 (+) Output - Programmable ����������������������������������������... -
Page 3: Pin Main Wire Harness
Installation Considerations BEFORE STARTING THE INSTALLATION, READ THIS ENTIRE MANUAL TO FAMILIARIZE YOURSELF WITH ANY INSTALL REQUIREMENTS • BE SURE TO VERIFY EACH CIRCUIT WITH A DIGITAL MULTIMETER • IDENTIFY WHICH CIRCUITS ARE REQUIRED FOR THE VEHICLE IN QUESTION • MOUNT ANY SYSTEM COMPONENTS AND ROUTE WIRING AWAY FROM MOVING PARTS OR PARTS OF THE VEHICLE THAT GENERATE EXCESSIVE HEAT • TAPE OFF OR REMOVE ANY UNUSED WIRING TO PREVENT... -
Page 4: Orange Wire - Accessory (+) Output
6 Pin Main Wire Harness (cont’d) ORANGE WIRE - ACCESSORY (+) OUTPUT This circuit is designed to drive accessory circuits like climate control, etc� It turns on when remote start is activated (slightly earlier than the primary ignition output) and turns off only during engine cranking�... -
Page 5: Violet/White Wire - Tach Signal Input
18 Pin Secondary Wire Harness (cont’d) CONNECTION (Manual Transmission): Connect this to the brake switch wire that shows (-) ground when the parking brake is engaged� VIOLET/WHITE WIRE - TACH SIGNAL INPUT This input provides the engine’s RPM signal to the remote start� This is typically the most reli- able form of engine detection�... -
Page 6: Red/White Wire - Trunk Release / 2Nd Channel (-) Output
18 Pin Secondary Wire Harness (cont’d) RED/WHITE WIRE - TRUNK RELEASE / 2ND CHANNEL (-) OUTPUT This output provides a 250mA negative output when the trunk release/CH2 function is activated by the controller� The output will remain as long as the controller button(s) is held� CONNECTION: Connect this wire to the vehicle’s existing trunk release switch if it is a low current negative circuit�... -
Page 7: Pin Secondary Wire Harness
6 Pin Secondary Wire Harness PINK WIRE - 3RD CHANNEL (-) OUTPUT This output provides a 250mA negative output when the CH3 function is activated by the con- troller� The output will remain as long as the controller button(s) is held� CONNECTION: Connect this wire to any desired add-on accessory that can utilize a negative activation input�... -
Page 8: Wiring Overview Diagram
Wiring Overview Diagram Window-mount Receive / Transmit Module Status Lights Remote Start Ac Valet Valet Switch - OR - Switch Status Lights OEM Alarm Arm / C OEM Alarm Disarm / CH5 Starter Interrupt WIRE LEGEND socket and relay Hard wire connection required Supported via DATA port(s) White cut starter... - Page 9 6 PIN AUX HARNESS 3 PIN SAT� RELAY PORT (RED) 3rd Channel (-) Output - PINK Start (-) Output - GREEN ctivation (-) Input - WHITE/BLUE Constant 12v (+) Output - RED Arm Alarm (-) Input - WHITE Ignition (-) Output - BLUE Disarm Alarm (-) Input - BROWN CH4 (-) Output - LT�...
-
Page 10: Pin Satellite Relay Port (Blue)
3 Pin Satellite Relay Port (BLUE) NOTE: There is no dedicated harness included� Use the RED 3-pin harness for this port� GREEN WIRE - ACCESSORY (-) OUTPUT This provides a 250mA negative output when the large ORANGE accessory wire is active� CONNECTION: If a negative starter circuit is needed, connect this directly to the vehicle’s nega- tive starter circuit�... -
Page 11: Green Data Port
Green Data Port This port provides a direct digital interface for any Omega IntelliKit, OmegaLink interface mod- ule, or other accessories� It can eliminate the need for several wire-to-wire connections� Refer to the wire diagram overview on page 8 to see which circuits are supported by this port and compare them to the data functions available from the interface module�... -
Page 12: Window Mount Antenna Module
Window Mount Antenna Module This system is equipped with an outboard receiver or transceiver (2-way) module� It is designed to be window mounted high on the windshield for optimal performance and range� It is best to mount this module using the double sided stick pad included (be sure to clean glass before adhering)�... -
Page 13: Programming Transmitters
Programming Transmitters Standard Programming: Using this method to program additional or replacement transmitters does not turn on or otherwise affect the Unauthorized Transmitter Alert (UTA) feature� Step 1 Have all transmitters which are to operate the system at hand� Then, turn the ignition “on”� Step 2 Within 5 seconds of turning on the ignition, press the Valet Switch 5 times�... -
Page 14: Programmable Features
Programmable Features PROGRAMMING FEATURES A matrix of all programmable features and their options are on the next page� For detailed information on each feature, please refer to the operation manual� Use the procedure below to make any necessary changes� NOTE: You can program features via your computer with Omega Weblink. Visit www.omegaweblink.com for more information. -
Page 15: Programmable Features Matrix
User Feature Programming: Ignition on, off, press valet 5 times Lock Button Unlock button Trunk button Start button Lock + Unlock # Feature (Brake x 1) (Brake x 2) (Brake x 3) (Brake x 4) (Brake x 5) 1 Remote Start Run Time 10 min 5 min 15 min... - Page 16 Temporary back cover. Color cover is in a separate file. IM_AL-XX60-EDPB-v2_6/20/2014...