Instructions For Chargers And Batteries - F.F. Group CJS 20V/80 PLUS Original Instructions Manual

CJS 20V/80 PLUS
Use power tools only with specifically designat-
f
ed battery packs. Use of any other battery packs
may create a risk of injury and fire.
When battery pack is not in use, keep it away
f
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a fire.
Under abusive conditions, liquid may be eject-
f
ed from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
SERVICE
Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the pow-
er tool is maintained.
SAFETY INSTRUCTIONS FOR JIGSAWS
Hold power tool by insulated gripping surfaces,
f
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting ac-
cessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give
the operator an electric shock.
Keep hands away from the sawing range. Do not
f
reach under the workpiece. Contact with the saw
blade can lead to injuries.
Apply the machine to the workpiece only when
f
switched on. Otherwise there is danger of kickback
when the cutting tool jams in the workpiece.
Pay attention that the base plate 7 rests secure-
f
ly on the material while sawing. A jammed saw
blade can break or lead to kickback.
When the cut is completed, switch off the ma-
f
chine and then pull the saw blade out of the cut
only after it has come to a standstill. In this man-
ner you can avoid kickback and can place down the
machine securely.
Use only undamaged saw blades that are in per-
f
fect condition. Bent or dull saw blades can break,
negatively influence the cut, or lead to kickback.
Do not brake the saw blade to a stop by applying
f
side pressure after switching off. The saw blade
can be damaged, break or cause kickback.
Use appropriate detectors to determine if utility
f
lines are hidden in the work area or call the local
utility company for assistance. Contact with elec-
tric lines can lead to fire and electric shock. Damaging
a gas line can lead to explosion. Penetrating a water
line causes property damage.
Secure the workpiece. A workpiece clamped with
f
clamping devices or in a vice is held more secure than
by hand.
Always wait until the machine has come to a com-
f
plete stop before placing it down. The tool insert
can jam and lead to loss of control over the power
tool.
INSTRUCTIONS FOR CHARGERS AND
BATTERIES
1. BATTERY CHARGERS
a. Before charging, read the instructions.
b. For indoor use. Do not expose to rain.
c. Do not charge non-rechargeable batteries.
2. BATTERY
a. The battery must be removed from the appli-
ance before it is scrapped.
b. The appliance must be disconnected from the
supply mains when removing the battery.
c. The battery is to be disposed of safely.
d. Do not use non-rechargeable batteries.
e. Do not crush, open or burn the battery. Exposure
to potentially harmful materials may occur.
f. In case of fire use C0
g. Do not expose to high temperatures >45°C. Cells
may degrade at high temperatures.
h. The battery must be charged by a constant cur-
rent, constant voltage transformer.
i. Charge battery regularly in conditions between
5°C to 45°C with the specified charger designed
for this battery.
j. Store in a dry, well ventilated area within the rec-
ommended limits of 10°C to 30°C.
k. Do not use battery if it has been stored at 5°C or
less. Allow it to "normalize" at room temperature
before usage/changing.
l. During decommissioning remove the battery cell
for recycling separately to the product, which is
covered by the waste electrical and electronic
equipment directive. Insulate the terminals with
adhesive insulating tape to prevent a short cir-
cuit, fire or explosion occurring.
CONNECTION TO THE POWER SUPPLY
Make sure the power supply information on the
machine's rating plate are compatible with the
power supply you intend to connect it to.
This appliance is Class II* and is designed for con-
nection to a power supply matching that detailed
on the rating label and compatible with the plug
fitted. If an extension lead is required, use an ap-
proved and compatible lead rated for this appli-
ance. Follow all the instruction supplied with the
extension lead.
*Double insulated: This product requires no
earth connection as supplementary insu-
lation is applied to the basic insulation to
protect against electric shock in the event of
failure of the basic insulation.
LITHIUM-ION MATERIAL DATA SHEET
As a substance under normal conditions of use it is
f
not considered a hazard to health. In the event of
accidental release, measures to prevent spread must
be adhered. Do not contaminate rivers, waterways or
drains.
Composition of lithium-manganese, lithium-cobalt
f
and lithium salt as the organic solvent electrolyte
(nonaqueous liquid).
Hazardous Decomposition: None during normal
f
operating conditions. If cell is ruptured hydrogen
fluoride and carbon monoxide may be released.
English |
dry chemical extinguisher.
2
www.ffgroup-tools.com
7