120/240 Vac Input Power Connection; Setting The Limit Switches - Eagle 100 Series Installation & Owner's Manual

Diamond DC Board 120/240 VAC Input Power Connection
WARNING: Eagle Access Control Systems, Inc. is not responsible for researching and complying
with local building codes. Be sure to check all local building codes before installation.
Be sure that the circuit breaker for the line input power is turned OFF before connecting the
input power to the operator.
All operators MUST be properly grounded. Installing surge protection is recommended.
120 VAC
Operator Wire Color Description
Black - 120 VAC (Hot)
White - Neutral
Green - Ground
(from an approved grounding method)
Junction Box
Black wire to Black wire.
White wire to White wire.
Green wire to Green wire.
120 VAC Input
Black
Power Wire
White
Green
Single Operator 120 VAC Input Wire
Guidelines
14 AWG 12 AWG 8 AWG
25 ft 50 ft 100 ft

Setting the Limit Switches

The limit switches MUST be set so the gate stops at the correct open and close positions.
the control board MUST have power for the limit LEDs when setting the limit switches.
Adjust the close limit switch FIRST when the gate is in the closed position.
Feature Selector #2
REVERSE LOOP NO
ONE PASS OFF
STOP-REVERSE OFF
ALARM-RESET OFF
CLOSE TIMER OFF
OPEN LEFT
Open and Close
Limit LEDs will light
up on control board
OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPENING CLOSING CLOS CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE LOS
for top or bottom
LIMIT LIMIT
limit switches as
GATE STATUS
indicated.
Top Limit Bottom Limit
Switch Switch
Indicates the
direction the
gate is cycling.
22
Diamond DC Board ONLY
CAUTION
240 VAC -
Operator Wire Color Description
Black - 120 VAC (Hot)
Gray - 120 VAC (Hot)
Green - Ground
Only use 2 wires of the
3 phase input power wire.
Terminate 3rd wire
(Do not use).
240 VAC
Three Phase
Input Power Wire
Single Operator 240 VAC Input Wire
6 AWG 14 AWG
200 ft 50 ft
SELECT
SLAVE MASTER
OPEN LEFT OPEN RIGHT
BRAKE OFF BRAKE ON
REVERSE LOOP NC
ONE PASS ON
STOP-REVERSE ON
ALARM-RESET ON
CLOSE TIMER ON
OFF—ON
OPEN RIGHT
OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPENING CLOSING
LIMIT
GATE STATUS
Bottom Limit
Switch
Indicates the
direction the
gate is cycling.
120 VAC power
outlet provided.
Single Phase
(from an approved grounding method)
Junction Box
Black
Gray
Terminated Wire
Green
Guidelines
12 AWG 10 AWG 8 AWG
100 ft 150 ft 200 ft
Top Limit Switch
Bottom Limit Switch
SLAVE
OPEN LEFT
BRAKE OFF
MH1 REVERSE LOOP NO
ONE PASS OFF
STOP-REVERSE OFF
ALARM-RESET OFF
CLOSE TIMER OFF
MH2
AUTO OPEN OFF
POWER FAIL OPEN
OPEN DELAY MASTER OFF
OPEN DELAY SLAVE OFF
REVERSE
LOOP
SHADOW
LOOP
EXIT
OPEN
MH3 MH4
REVERSE
REVERSE LOOP
#1
RELAY
CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE CLOS LOS
RELAY
24VDC
-24VDC
LIMIT
OPEN
#2
3-button
STOP
CLOSE
station
Top Limit
cycles
Switch
operator.
Junction
Box
MASTER/SLAVE LINE INPUT POWER
NOTE: The VAC input power for the
master and slave operators MUST be on
the same circuit breaker.
IMPORTANT: DO NOT cycle the
operator before setting the limit
switches. Damage or injury could
occur if limit switches are NOT set.
(See below)
To Set the Limit
Switches:
Loosen set screw and
rotate top and bottom
limit switch activators
accordingly.
Top Limit Switch Activator
Set Screw
Bottom Limit Switch Activator
Power Switch
OFF ON
SELECT ACTIVE LIGHT HEAVY
MASTER
OPEN RIGHT
OPEN OPENING CLOSING CLOSE
BRAKE ON
REVERSE LOOP NC OVERLOAD LIMIT LIMIT
ONE PASS ON OPENING CLOSING
STOP-REVERSE ON
ALARM-RESET ON
CLOSE TIMER ON TIMER ERD STATUS GATE STATUS
OFF—ON
PWR FAIL OPERATION
0 1
AUTO OPEN ON + –
POWER FAIL CLOSE OFF 1
OPEN DELAY MASTER ON OFF 2
OPEN DELAY SLAVE ON OFF 3 M/S PHASE RESET
OFF—ON P/O ADJUST
20
SHADOW EXIT
FUSE MAX 20A
FUSE MAX 35A
20 Amp
AC POWER SOLAR
24VAC POWER
SHADOW LOOP EXIT LOOP
LOW CHARGER
BATTERY ON
+ –
#3 #4 #5 #6 #7 #8 #9 #10 #11 #12 #13 #14
MAG LOCK
POWER 24 VDC
SLAVE MASTER
+ –
+ – + –
GLOBAL INPUTS OUTPUTS COMM PORT