Eagle II Installation Manual
  1. Manuals
  2. Brands
  3. Eagle Manuals
  4. Gate Opener
  5. Power II
  6. Installation manual

Eagle II Installation Manual

1/2 hp swing gate operator
Hide thumbs Also See for II:
Table of Contents

Advertisement

Quick Links

See also: Installation & Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for Eagle II

Summary of Contents for Eagle II

  • Page 2: Table Of Contents

    All rights reserved. No part of this manual may be reproduced in any means: graphics, electronics, or mechanical, including photocopying without the expressed written permission of the publisher. Materials, components and specifications are subject to change without notice. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com...

  • Page 3: Ul Listings

    A wireless contact sensor shall function under the intended end use conditions. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com...
  • Page 4 Commercial / General access vehicular gate operator - Class IV - A vehicular gate operator operator - Class II - A vehicular gate operator (or system) intended for use in a guarded (or system) intended for use in a commercial...

  • Page 5: Installing The Warning Sign / Precautions

    ____________________ CAUTION! Be sure to read and follow all the Eagle Access Control Systems, Inc. and UL instructions before installing and operating any Eagle Access Control Systems, Inc. products. Eagle Access Control Systems, Inc. is not responsible for any improper installation procedures caused by failure to comply with local building codes.

  • Page 6: Methods Of Installation / Compact Installation

    F / G / H be sure that both arms 29" 21.5" 11" 23.5" are fully EXTENDED and LOCKED. Failure to follow these GATE CLOSING instructions could result in serious injury. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com...

  • Page 7: Mounting The Secondary Entrapment / Welding Gate Arn

    EAGLE-II Swing Gate Operator ____________________ Mounting The Secondary Entrapment Note: Eagle Access Control Systems, Inc. recommends the installation of a photocell sensor . Receiver All Secondary Entrapment Transmitter Sensors Are Connected To Edge Sensor Inputs EXAMPLE OF PHOTOCELL SENSORS ____________________...

  • Page 8: Mounting Operator(S) To Concrete Pad(S)

    To select the opening direction of the gate, use the Feature Selector (as shown). Move switch #2 to the "open left" position for left opening. Move switch #2 to the "open right" position for right opening. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com...

  • Page 9: Connecting The Power / Reverse / Exit Loop Installations

    TWISTED WIRES up the grooves REVERSE LOOP with a proper sealant. EXIT LOOP PROPER SEALER SHOULD WIRE LAYERS BE USED IN LOOP CUTS IN LOOP CUT Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com...

  • Page 10: Two Way Adjustable Reverse Sensors / Erd

    Not Sensitive enough = if the gate strikes an object and does not stop or reverse Not Sensitive enough = if the gate strikes an object and does not stop or reverse Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (10)

  • Page 11: The Feature Selector

    Note: If the power light is on and the operator does not function, press the reset button once. If this does not solve the problem, proceed with turning off the power switch and then switching it back on again. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (11)

  • Page 12: Conencting Accessories

    EAGLE-II Swing Gate Operator ____________________ Connecting The Accessories Photo Eye MAG Lock Reverse Loop Phantom Loop Key Lock Box Fire Lock Box Edge Sensor Exit Loop Phone Entry System Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (12)

  • Page 13: Master & Slave Operations

    Master Control Options Use the feature selector on the master operator to choose available features by designating the various switches (2 through 4). Gate opening direction, motor brake and close timer. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (13)
  • Page 14 "off" position. Switch #2 Set to the "open left" or to the "open right" position. Switch #3 Set motor to "ON" or "OFF" position. Switch #4 Set to "OFF" position. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (14)

  • Page 15: Output Connections

    5 minutes. On the Board, you have two options of reset mode. Power (24 VAC) The Control Board provides 24 VAC Power, which can be used for loop detectors and receivers. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (15)

  • Page 16: Description Of Inputs

    Once activated the gate will fully close. Activation while the gate is opening has no effect. Multiple devices may be connected in parallel to the Edge Sensor Input. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (16)

  • Page 17: Receiver Connections

    Gate Travel Distance / Setting The Limit Switches The limit switches must be set so that the gate stops at the proper position. Limit Switches Loosen Screws Make Adjustments Tighten Screws Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (17)

  • Page 18: Emergency Release

    Depending on the weight of the gate clutch slippage may occur. Typical Clutch slippage is about 1/4 turn. If it does not slip, readjust the Clutch accordingly. Use an appropriate wrench to adjust the clutch Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (18)

  • Page 19: Troubleshooting

    (B) Safety Loop Detectors must be connected to the Reverse Loop input. (C) If the "Timer to Close" function is desired, switch #4 must be set to the "on" position. (D) It is Ok to call the Eagle Access Customer Service Department with any questions...we are here to serve YOU! 1-800-708-8848 Eagle Access Control Systems, Inc.

Table of Contents