Diamond Board Adjustments And Wiring; Diamond Board; Features Selector Switches #1 - #8 - Eagle 100 Series Installation & Owner's Manual

DIAMOND BOARD ADJUSTMENTS AND WIRING

M/S Phase
DO NOT remove jumper or operator will NOT function.
Designates communication between master and slave
operators only. M/S operators can be set for the same
or opposite phase, depending on operators
communication (can vary).
Reset Button
Press for soft reset of operator (reset board logic).
Turns OFF activated alarm. Try this button before
preforming a hard shutdown of operator (turn
power switch OFF/ON) when operator fails.
In-Ground Loop Wires Connection
Connect in-ground loop wires to
corresponding loop detector Only when
using Eagle Plug-In Loop Detectors.
EG167
Loop Detector
Sensitivity
Push & hold Reset/Sen. button
LED will blink from 1 to 4 times. Release
button upon reaching desired sensitivity.
1 = Very Low, 2 = Low,
3 = Normal, 4 = High
To change from inductive loop to
mini-loop- see instructions.
Indicators
Green - Steady indicates power
Fast blink - Shorted loop
Slow blink - Open loop
Red - Detect Indicator
Eagle Plug-In
Loop Detector
Automatically adjusts for
proper sensitivity. Eagle
brand are designed for
"Fail-Safe" operation.
Feature Selector Switches #1 - #8
The Feature Selector Descriptions:
NOTE: The power MUST be turned OFF before changing the features selector switches.
Switch #1: Slave/Master - Sets the operator to work as Master or Slave. Single operator
MUST be set to MASTER.
Switch #2: Gate Opening - designates left or right opening direction.
Switch #3: Motor Brake - If the ON position is selected, the gate will stop instantly when
the limit switch is activated. This is useful for uphill/downhill applications and on all fail-safe operators.
Switch #4: Reverse Loop - Sets the reverse loop to be normally open (NO) or normally close (NC). It is useful in fail-safe applications.
Normal setting is OFF (Normally Open).
Switches #5 - #8: Switch #1 ON - Master Setting ONLY
NOTE: For switches #5 - #8: Switch #1 OFF - "Slave Setting", see page 15 "Gate Delay Functions" for descriptions.
Switch #5: One Pass (ON/OFF) - This tailgating feature works with the reverse loop to allow only one vehicle to pass the gate. After the vehicle
passes, the gate closes instantly. If a second vehicle approaches, the gate stops. The gate resumes closing after the vehicle leaves.
Switch #6: Stop-Reverse (ON/OFF) - The radio feature allows the transmitter to work as a three-button station and is useful for a partial
opening. If selected, the first command will open the gate, the second command will stop the gate and the third command will close the gate.
Switch #7: Alarm Reset (ON/OFF) - If the ON position is selected, after the five minute "Shutdown" time period, the operator will reset and any
input will be accepted. Normally, the power must be turned off to reset.
Switch #8: Close Timer (ON/OFF) - Turns the close timer ON or OFF. See page 12.
Diamond Board ONLY
Feature Selector
See below
SLAVE
OPEN LEFT
BRAKE OFF
REVERSE LOOP NO
OPN DLY S
OPN DLY M
OPN DLY S
OPN DLY M
REVERSE
LOOP
SHADOW
LOOP
EXIT
OPEN
REVERSE
Eagle Plug-In
Loop Detector
Power
Connections
Detect
See instructions
EG167
on the Eagle loop
detectors when
Vehicle
Detector
Reset
using them.
REVERSE LOOP
#1
GND
Radio Receiver
RCVR
24VAC
See page 13
GND
OPEN
#2
STOP
3-Button Station
Cycles Operator
CLOSE
Wiring Accessories - See page 14
Close Timer -
See page 12
or
M/S Gate Delay -
See page 15
Reverse ERD Sensor
See page 12
SELECT
ACTIVE
MASTER
OPEN RIGHT
BRAKE ON
REVERSE LOOP NC OVERLOAD
OPENING
ONE PASS
STOP-REVERSE
ALM-RST
CLOSE TIMER TIMER ERD STATUS
OFF—ON
0 1
M/S PHASE RESET
SHADOW EXIT
Power
Detect
EG167
Vehicle
Detector
Reset
SHADOW LOOP EXIT LOOP
#3 #4 #5 #6 #7 #8
GLOBAL INPUTS
Global Inputs
Descriptions - See page 13
REVERSE LOOP NO
Limit Switches
See page 10
LIGHT HEAVY
OPEN OPENING CLOSING CLOSE
LIMIT LIMIT
CLOSING
GATE STATUS
Eagle Diamond Control Board
Rev A4
#9 #10 #11 #12 #13 #14
POWER
SLAVE MASTER
+ – + –
OUTPUTS COMM PORT
Outputs Master/Slave
See page 12 See page 15
SELECT
SLAVE MASTER
OPEN LEFT OPEN RIGHT
BRAKE OFF BRAKE ON
REVERSE LOOP NC
OPN DLY S ONE PASS
OPN DLY M STOP-REVERSE
OPN DLY S ALM-RST
OPN DLY M CLOSE TIMER
OFF—ON
Factory Set
ERD Sensor
"Fine Tune"
Adjustment.
Please call
Eagle
Access
before any
adjustment.
See page 12.
Fuse
15 Amp
250V
Slow-Blow
9