1. Manuals
  2. Brands
  3. logitrans Manuals
  4. Forklifts
  5. HS 1000RF-SEMI
  6. Manual

logitrans HS 1000RF-SEMI Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HS 1000RF-SEMI

Advertisement

Table of Contents
loading

Related Manuals for logitrans HS 1000RF-SEMI

Summary of Contents for logitrans HS 1000RF-SEMI

  • Page 1 HS 1000RF-SEMI...
  • Page 2 Denmark It is hereby declared that: Machine: Product group: Stackers Type: HS 1000RF-SEMI/HSS 1000RF-SEMI Year of manufacture/ Serial No.: a) Has been manufactured in conformance with the stipulations of the: • Directive no. 2006/42/EC b) Has been manufactured in conformance with the stipulations of the standard: •...
  • Page 3 1.0 Before the first lift... The Logitrans Stacker is manufactured in accordance with safety directives. Among the subjects dealt with in this Instruction Manual are: • Proper application • Physical limitations of the product • Risks with improper use Therefore please read this Instruction Manual carefully!
  • Page 4 2.0 How to operate the stacker 2.1 Handling of pallets For proper operation, stand behind the handle. Push/pull - pump. HS RF-SEMI...
  • Page 5 2.0 How to operate the stacker 2.2 The three release lever positions 1. Quick Lift 2. Normal Lift 3. Lowering 2.2.1 Quick Lift 0 - ca. 300 kg 2.2.2 Normal Lift ca. 300 - 1000 kg 2.2.3 Lowering...

  • Page 6: Optimum Safety

    3.0 Optimum safety 3.1 Avoid overloads The maximum load must not be exceeded. Remember, the stacker is designed for evenly distributed load, - goods on pallets etc. If the forks are pointloaded on one side there is a risk of bending. 3.2 Avoid offset loads The load must be evenly distributed.

  • Page 7: Emergency Braking

    3.0 Optimum safety 3.4 Transport with load The stacker is designed for use on even and level floor. During transport the forks shall be raised as little as possible. Transport with raised forks should be made over the shortest possible distances and at low speed. 3.5 Emergency braking ...

  • Page 8: Safety Regulations

    3.0 Optimum safety ATTENTION Moving parts Safety regulations • Never walk under a raised load! • Before lowering the forks, make certain that no foreign elements can hinder the free lowering of the forks. • The stacker is designed for use on an even and level floor. •...

  • Page 9: Oil Change

    4.0 Long live the stacker Regular inspection and the replacement of worn or defective parts in good time will prolong the life of the stacker. “Prevention is better than repair”, therefore ensure: • Correct usage • Regular cleaning • Periodic safety and service inspection 4.1 Lubrication and hydraulic oil All ball bearings are lubricated with a lubricating grease for the food industry, and all moving parts are treated with a grease for the food...
  • Page 10 4.0 Long live the stacker 4.3 Replacement of valve insert(s) If all fault remedy possibilities (See middle pages) have been tried without satisfactory results the entire valve insert must be replaced. Low-pressure valve insert 160094: The insert contains both the valve control system and a pressure relief valve.

  • Page 11: Bleeding The Hydraulic System

    4.0 Long live the stacker 4.6 Bleeding the hydraulic system The pump will not operate throughout its whole pump stroke if there is air in the hydraulic system. - The system can be bled as follows: 1. Pump the forks up to the top and sink them quickly 2.
  • Page 12 4.0 Long live the stacker 4.8 Adjustments of lowerimg mechanism The lowering mechanism is adjusted correctly if: Quick lift = when the release lever is in bottom position Normal lift = when the locking pawl of the release lever is If this is not the case, adjust as follows: 1.

  • Page 13: Fork Adjustment

    4.0 Long live the stacker 4.10 Fork adjustment Two rollers on the fork bracket are mounted on eccentric pins so that they can be adjusted. Adjustment: 1. Loosen screws pos. 91 (5 mm). 2. Pin pos. 56 can now be turned to give the necessary adjustment (8 mm).
  • Page 14 5.0 Fault location key When the stacker is used every day, adjustments and the replacement of worn parts might be necessary. BEFORE ASKING THE DISTRIBUTOR FOR ASSISTANCE..TRY THE FAULT LOCATION KEY! SYMPTOMS AND SIGNS Forks move up and down with pump strokes The stacker does not lift to maximum height The load is difficult to pump with the handle in its normal position The forks do not lift quickly when the handle is in its Quick position...
  • Page 15 Cause Mending See point 3.3 Load heavier than the max. permissible Oil deficiency See point 4.1 Valve control system needs adjustment See point 4.3 Low pressure valve insert (160094) (control valve) Seal leakage See point 4.4 Valve cone does not seal completely Frequently concerning high pressure See point 4.5 valve insert (400672E)
  • Page 16 Such affected parts shall be sent to your Logitrans dealer carriage paid within the warranty period in force at the time in question, together with a copy of the documentation for the service performed (B284 - see the back page).
  • Page 20 Periodic service check Service check is required once each year, or at least for every 250 hours of operation The service check is to be performed on the basis of form no. B280 and proved on form no. B284. Forms and instructions for the service check are available at your dealer.

Table of Contents